其他颜色的键槽没有这个标识。
键槽插槽工具的位置。
键槽中置有分离卡簧座，并夹装有分离卡簧；
A separating clamp spring seat is arranged in the key groove which is provided with a separating clamp spring.
提出了两种曲轴齿轮轴颈键槽位置误差的检测方法。
Two kinds of inspection methods of the position error of key slot an gear journal of crankshaft have been proposed.
键槽是全钢，深红色，并注有“火警专用”的标识。
The all-steel box is deep red with the required signage "Fire Dept Use Only."
一种测量机械零件位置误差的轴键槽对称度检测仪。
The utility model relates to a symmetrical characteristic detector for the axial key groove which can measure the positional error of the machine parts.
带自位球轴承的杆端。长螺纹杆和键槽。尺寸和负荷。
Rod - ends with self - aligning ball bearings. long threaded shank and keyway. dimensions and loads.
由于我们现在有了震击器，我们就能够解决键槽卡钻了。
Since we have jars, we are able to solve key-seating sticking now.
由于我们现在有了震击器，我们就能够解决键槽卡钻了。
Since we now have jar, we are able to solve key-seating sticking.
带自位球轴承的杆端。无键槽的长螺纹杆。尺寸和负荷。
Rod - ends with self - aligning ball bearings. long threaded shank without keyway. dimensions and loads.
并对键槽对称度公差及检测方法的确定作了进一步的探讨。
Whereas, it further discusses how to determine symmetry tolerances of the key slots and how to select methods for measuring and test.
键槽式、设置螺栓式或锥式直接输入的外箱应采用调配器法兰。
An adapter flange will be needed in the case of the direct input method with a key type, set screw type or taper collet type.
在壳体上安装齿轮箱，确保齿轮箱轴键妥当地固定在耦合键槽中。
Mount gearbox on housing, assuring that coup ling key slot accepts gearbox shaft key properly.
介绍塑料齿轮键槽和轮毂的设计原则，以及常见的结构设计方法。
This paper introduces the design principles of keyslot and hub of plastic gear and common methods of structural design.
这个出格地掉败是加快由急弯时说，已被削减，在轴地矩形键槽。
This particular failure was accelerated by the sharp corners that had been cut in the shaft's rectangular keyway.
同级扬压力作用下，带键槽底板块的应力大于直缝底板块的应力；
The stress in floor plate with keyway are more than it with straight seam under the same level of uplift pressure.
本文讨论带有键槽的施工缝时大体积混凝土结构的应力分析方法。
In this paper, the stress analysis method of massive concrete structure in consideration of construction joints with key grooves is discussed.
针对轴类零件键槽精度的要求，介绍了一种专用夹具及对刀方法。
Pointing to the accuracy requirement of the keyway on shifts, this paper presents a special jig and a cutter positioning method.
铣刀系列：直柄铣刀、直柄键槽铣刀、锥度铣刀以及其它非标铣刀。
Milling cutter series: straight shank milling cutter, straight shank keyway milling cutter, prick milling cutter, nonstandard milling cutter.
利用V型块自动对中定位原理，对飞轮键槽拉床定位塞尺进行改进。
Improvement is made to the positioning feller gauge in flywheel keyway broaching machine by V-type auto center align.
本文提供了生产中实用的键槽对称度误差检测方法和数据处理公式。
The paper prov rides a practical method of measuring and assessing the symmetrical error of the keyway in production and data processing formula.
键槽轮毂的锥孔应至少有70%的着色（表面接触）转移到锥度计上？
Tapered bores for keyed hubs shall have a minimum of 70% transfer of bluing (surface contact) to the taper gage.
本文研究了该舵装置键槽的加工工艺以及为加工键槽而设计的专用机床。
This is a presentation of the keyway installation of the rudder processing and for the processing and design of the keyway dedicated machine.
传动轴、螺旋弹簧、传动轴上的键槽、滑块、前限位和后限位等部分。
It includes driving shaft, helical spring, key way on the driving shaft, block, front stop unit, back stop unit, etc.
目前对于十字头万向接轴整体式轴承座键槽的受力计算尚无简便确切的方法。
So far there has been no simple and correct calculation approach available for computing the stress distribution in the key slot on the integral cross pin type journal bearing rest.
常用的指标包括与键槽齿轮，开槽盘，轴等的碳素钢，铁，或磁性不锈钢制造。
Commonly used targets include gear teeth, slotted discs, shafts with keyways, etc. made of carbon steel, iron, or magnetic stainless steel.
最后，在组装过程中，当部件通过键槽时，注意避免损坏密封和轴的轴颈表面。
Lastly during assembly care is taken to avoid damaging the seals when passing over the keyway or performing bearing surfaces of the shaft.
此电机的电机轴两端伸出分别同一风叶和一皮带轮通过键槽和键相 配接固定；
Two ends of the motor shaft of the motor respectively extend to match and fix with an impeller inducer and a belt pulley through a key slot and a key.
论述了键槽对称度误差的产生原因以及检测方法，并对有关计算公式进行了探讨。
This paper discusses the cause of keyway symmetry error produced and test method and approaches to related calculating formulae.
论述了键槽对称度误差的产生原因以及检测方法，并对有关计算公式进行了探讨。
This paper discusses the cause of keyway symmetry error produced and test method and approaches to related calculating formulae.
应用推荐