依据锥角堆积模型讨论了协萃反应机理。
The extraction mechanism of uranyl nitrate is discussed in terms of a cone-angle model.
文中还分析了背压对穿透、雾化锥角等的影响。
The effects of back pressure on the spray penetration, the spray Angle, etc. are also discussed.
该方法考虑了来流、锥角和钝度对底部热的影响。
The influences of free flow, cone Angle and bluntness are considered.
喷雾锥角和喷雾均匀度是燃油喷嘴的两个重要指标。
Atomization Angle and uniformity are two key parameters of fuel spray nozzle.
研究了半锥角和液膜破碎前长度随液压差的变化规律。
The variations of nozzle liquid pressure on half-cone angle and breakup length have been analyzed.
法所确定的尾锥角略有偏低，但仍可用于弹丸的初步设计。
This method is convenient and effective for the primary design of projectile shapes.
通过实验和分析，得出了力能参数较低而成型较好的模具锥角。
Reasonable die tapers, which can reduce the values of stress parameters and improve forming, are obtained based on experiments and analysis.
油嘴的喷油锥体形式及喷油锥角对现用加热器的性能影响不大。
Different forms of injection cone and different injection cone Angle have little influence on current heaters.
分析了弹头长度、弹丸质量和靶板材料参数对临界半锥角的影响。
The effects of nose length, projectile mass, and the mechanic performance of plate material on the plugging failure were analyzed.
然而尚未见到关于立辊锥角对翼缘宽展的影响进行定量分析的报道。
However, it is not seen that quantitative analysis on the effects of vertical roller cone Angle on the flange lateral spread has been performed by far.
在摩擦角小于半锥角的情况下，给出了极限承载能力的近似计算公式。
The approximate formula for limit load is found when the fraction angle is less than the half conical one.
文丘里管的喉部直径、入口锥角和出口锥角对空化效应有着重要的影响。
The gular diameter and inlet angle and outlet angle of the Venturis have an important influence upon hydrodynamic cavitation.
运用有限元法分析了不同入口锥角的陶瓷喷砂嘴冲蚀过程中的应力状态。
The stress states of the ceramic nozzles with different entrance angle in the sand blasting process are analyzed with finite element method .
分析了圆锥壳结构的径厚比、长径比及锥角变化对结构应力响应的影响。
The effects of R/h ratio, L/R ratio and cone angle on the dynamic response of the conical shells are discussed in this section.
伞形喷雾径向贯穿距离远小于多孔喷雾，喷雾锥角在喷雾早期急剧减小。
However, the radial penetration distance of umbrella spray was much shorter than that of multi hole spray and the umbrella spray Angle decreased rapidly in the early stage of spray development.
推导出蜗轮齿顶圆锥的理论锥角计算公式及齿根圆锥的理论锥角计算公式。
The computing formula of theoretical cone angle of the wormwheel addendum cone and dedendum cone can be derived yet.
机床除根锥角需要手动调整外，切削运动均为菜单式操作，由程序自动控制。
The machine cutting is menu operation controlled by the program automatically except adjusting the cone angle by hand.
文中叙述了转鼓的强度计算、振动计算、减振设计、锥角与过滤介质的选用等。
The authors deal with the calculating of the strength and vibration, the design of vibration absorption, the select of the taper and the filtrating medium, etc.
背压对贯穿距离、喷雾锥角、喷雾轴心速度和浓度衰减率的影响均大于启喷压力。
It shows that the effects of back pressure on penetration, spray cone Angle, and decline rate of centerline velocity and concentration of the spray are greater than that of fuel injection pressure.
结合六齿矩形花键轴实际成形情况进行模拟计算，获得了入模半锥角的较佳取值范围。
By numerical simulation of a six-tooth rectangle spline, the optimized half-angle of the concave die can be got.
斜轧穿孔机轧辊形状设计十分重要，其中辗轧锥角的正确设计是获得高精度壁厚的关键。
Proper design of roller cone angle of smooth rolling is the key to obtaining a high accurate wall thickness.
在燃烧室壁面附近，柴油的喷雾锥角迅速增大，而DME喷雾锥角几乎没有明显的变化。
Near the chamber wall and impingement spray, the spray angle of the diesel fuel spray increased very fast, but that of the DME spray almost had no significant change.
例如，除了位置、方向和光线颜色，它还能够控制spotlight锥角和锥体离心值。
For example, in addition to the location, direction, and color of the light, it's possible to control the Angle of the spotlight cone and the center bias of the cone.
测得不同液压差下离心喷嘴锥形液膜的各项特性参数，如液膜半锥角、液膜破碎前长度等。
Also, the characteristic parameters of conical liquid sheet with centrifugal nozzle, such as half-cone Angle and breakup length, were measured under different liquid pressures.
该机可用于磨削各类形似半圆角或反锥角的高速钢和硬质合金雕刻刀具和单边或多边刀具。
For grinding HSS and carbide engraving cutter as well as single lip or multiple lip cutters of various shapes such as radiused cutters or negative taper Angle of cutters.
针对大于5度的大锥角圆锥滚子加工工艺的特殊性，进行反复试验，摸索出可行的加工工艺。
For processing specificity of big cone Angle with exceeding5 degrees, the tests were repeatedly conducted so as to explore feasible processing technology.
计算结果表明，轴向预紧力随锥角或锥角差的增大而增大，密封系统承载内压能力随之下降。
The results obtained by FEM calculation indicate that the axial preloading force increases and the power of supporting inside pressure declines with the increase of taper or difference of taper.
研究了不同锥角的轴棱锥对涡旋光束聚焦特性的影响以及不同拓扑电荷数对聚焦特性的影响。
The influence of by different cone angles of the axicon and the different topological number of the vortex beam on the focusing properties of vortex beam is investigated.
在一个实施例中，可包括第三收集光学器件414来减小来自第二波长转换元件412的光的锥角。
In one embodiment, a third collection optic 414 May be included to reduce the cone Angle of the light from the second wavelength converting element 412.
在一个实施例中，可包括第三收集光学器件414来减小来自第二波长转换元件412的光的锥角。
In one embodiment, a third collection optic 414 May be included to reduce the cone Angle of the light from the second wavelength converting element 412.
应用推荐