将进气管与复卷机空气过滤器的进气管相连，然后进入电源。
Connect Intake-tube with intake-tube of air filter of the rewinder, then get through entering power source.
射流体与进气管通过活络接头连接。
The jetting body is connected with the intake pipe through a flexible joint.
这就防止废气倒流入进气管。
This prevents the intake charge from being blown out the exhaust.
本设备是专用于发动机进气管的密封性检测。
This equipment is dedicated to the engine intake pipe sealing detection.
从进气管道的锁手柄上拆下螺栓、垫圈和螺母。
Remove the screws, washers and nuts from the lock handles for the air inlet duct.
气伞内置软状进气管，与车内压缩空气室连接。
The ballute is internally provided with a soft intake pipe which is connected with the compressed air chamber in the truck.
外形设计上最引人注目的是车辆前端、车身以及进气管。
The exciting front end with its deep front apron and large air intake vents surges on uncompromisingly.
潜水附件。潜水服进气管。安全性技术要求和检验方法。
Diving accessories. Snorkels. Safety requirements and test methods.
将进气管接至复卷机空气过滤器进气接口，接通输入电源。
Connect Tntake-tube with intake-tube of air fliter of the rewinder, then get throagh entering power source.
风门表面留有安装摩托车进气管和发动机进气歧管的位置。
The Throttle body provides surfaces for mounting between the Motorcycle's air intake duct and the engine intake manifold.
发动机的进气系统主要由空气滤芯和进气管道两部分构成。
The air intake system of the engine is mainly composed of two parts: the air filter element and the intake pipe.
结果表明：采用谐振型进气管能明显地改善发动机的充气特性。
The results show that the volumetric efficiency of engines can be improved by the resonant intake system.
汽车设计你车的进气管应尽量安静的单位，可以装在你的引擎舱。
Automakers design your vehicle's intake tube to be the quietest possible unit that can fit in your engine compartment.
公司有多年生产消声器进气管总成、波纹管、金属软管的专业经验。
The company has many years of production muffler intake manifold assembly, bellows, metal hose of professional experience.
如果这时重启发动机，水会进入进气管内部，直接造成发动机爆缸。
If then restart engine, water will enter into the intake pipe internal, inflicting engine detonation cylinder.
两位五通阀(8)的控制端通过开关(11)与压缩气进气管连接。
The control end of the two-position five-way valve (8) is connected with a compressed air inlet pipe through a switch (11).
或不用抽气机，而在进气管道有一接高压清洁空气的进气口(4)。
Otherwise, the air exhauster is not necessary, and the air inlet (4) connecting with the high-pressure clean air is arranged in the air inlet pipeline.
轿东发动机缸盖、进气管、冷芯机、射芯机、铸造模具、出口铸件等。
Head-cylinder and Intake of non-Ferrous metal, Pouring machine for gravity die, Cold-box machine, Core-Shooting machine, Casting Mold, Exports'casting etc.
解决办法：需检查喷油器的雾化状况以及进气管是否畅通，有无堵塞物。
The solution: Need to check the atomization of the injector and the intake pipe is smooth or not.
在对铸件工艺和结构特征分析的基础上，进行了进气管消失模模具的设计。
Based on analyzing the technology and structure features of lost foam process cast, the designs of the inlet connection dies have been done.
并分析了在CA488进气管中装入亥姆赫兹谐振器对发动机性能的影响。
The effect of installing the Helmholtz resonator in CA488 engine air intake manifold on engine performances is also analyzed in this paper.
项目建设背景：采用以PA12为主要原材料，进行共混改性，生产汽车进气管。
Project Outline: This project is to use PA12 as the main raw material, which is blended and modified, to produce automobile intake pipe.
在发动机负荷变化即进气管压力变化时，阀芯的位移更大，燃气输出量的响应更快。
Load change in the engine intake manifold pressure changes that is when the spool displacement greater, gas output in response to faster.
本文主要通过数值仿真方法研究了进气管可变技术对汽油机流动特性及其性能的影响。
By using numerical simulation method, this paper mainly researches the influence of variable intake manifolds on intake flow characteristics and performance for gasoline engine.
试验结果表明，此装置得出的流量值比原在进气管道出口截面处得出的流量值误差小。
The test shows that the errors are less than those from measuring at cross section of outlet.
利用排气管温度加热汽化乙醇并通过进气管道供入气缸，与原机进行了性能对比试验。
Diesel engine, which was mixed with ethanol boiled by the preheated exhaust gas pipe and supplied into cylinder via air intake, was compared with the engine fueled only with diesel in this paper.
进气管(40)连接在气缸盖(20)的上表面和空气滤清器(22)的上表面之间。
An intake pipe (40) connects between the upper surface of the cylinder head (20) and an upper surface of the air cleaner (22).
在传热模型中，除考虑传导和对流换热外，也考虑了电池和空气进气管之间的辐射换热。
Radiation between cell tube and air feed tube and heat transfer by convection and conduction was also included in this model.
简体的长度、进气管和排气管的尺寸以及锥体和下料管是设计旋风分离器时要考虑的重点。
The focal points of designing cyclone separator were involved in cylinder length, dimension of inlet and outlet pipe, cone and filling tube.
简体的长度、进气管和排气管的尺寸以及锥体和下料管是设计旋风分离器时要考虑的重点。
The focal points of designing cyclone separator were involved in cylinder length, dimension of inlet and outlet pipe, cone and filling tube.
应用推荐