在最后一节臂刚要伸出之前停止拧紧和调整螺母。
Stop fastening and adjusting the nut before the last segment of the boom is to be extended.
如果还留有某些间隙，就稍微拧松调整螺母(对于起重臂缩回)。
If there's still some clearance, slightly loosen the adjusting nut (for retraction of the boom).
若发现压力阀的压力不太理想，可微调压力阀的调整螺母。以获得到理想数值。
If the pressure is not found ideal, you can trim the adjusting nut to get ideal value.
两杆轴承调整螺母上的果酱，使轴是垂直的(在直角)执行此操作的其他转向到地面。
Adjust the jam nuts on both rod bearings so that the axles are perpendicular (at a right Angle) to the ground.
若调整握把螺母后仍达不到间隙尺度值，则应将固定拉线调整螺母的支架向上提一下。
If after adjusting the wrap nut still cannot meet clearance dimension value, the case shall then be fixed farrowed adjustment nut stent upward mention.
柴油机横臂导杆折断会带来严重后果，经分析认为其折断原因有：同名气门杆顶部不齐；调整螺母松动，调整螺钉窜动；气门导管与气门杆间隙量大。
The reasons are: different top heights of valve rods having the same names; loose adjustment nuts or adjustment screws moving; and big clearances between valve guides and valve rods.
它被悬挂起来，并通过弹簧安装在磁桥内，两个铆钉和可调蝶形螺母可调整从检测表面到传感器的高度。
It is suspended and spring mounted within the Magnetic Bridge by two studs and adjustable wing nuts allowing the adjustment of the height of the sensors from the inspection surface.
这种管接螺母的调整能够弥补TFE阀座的磨损，避免由于拆卸阀门进行内部调整作带来的损失。
Adjustment of this union nut can compensate for wear of TFE seats, with no production loss to remove valve for internal adjustment.
调整后，拧紧锁紧螺母。
采用单独调整时，每个轴承配置使用螺母、垫片、间隔套、变形套等分别调整。
With individual adjustment, each bearing arrangement is adjusted separately using nuts, shims, spacer sleeves, deformable sleeves etc.
调整后，就将锁紧螺母拧紧。
通常可以通过对阀门排气口减压和重新调整衬垫螺母来阻止泄漏。
The leaks can usually be fixed by depressurizing the valve outlet and retorquing the packing nut.
把行程开关摇臂螺母松开，将摇臂往前调即可，如多次调整无效，请检查开关是否损坏。
Then loose the rocker nut of journey switch, and adjust the rocker to front, if after adjusted for many times still not available, then please check the journey switch whether was damaged or not.
锁紧二连杆的调整机构和瞄准镜中部的二个光楔锁紧螺母（图1序号7）。
Lock adjusting mechanism of two connecting rods and two optical wedge lock nuts of sighting telescope center (No. 7 in Fig. 1).
前方固定的，后面的移动调整和方法定在鼓当你不断旋转，我用了一个螺栓和螺母，在每个磁体。
The front ones fixed, the rear ones mobile with adjustment and method to fix in the drum when you get constant rotation, I used one bolt and nut in each magnet.
当所有的调整已经完成，锁螺母必须加紧了对黑色机壳的每个[3 ]每桶螺栓。
When all adjustments have been finalized, the lock nuts must be tightened down against the black casing for each of the [3] barrel bolts.
连接调整器。把调整器紧固在钢瓶上，安全地上紧入口螺母。
Attach the regulator. Fasten the regulator to the cylinder and tighten the inlet nut securely.
除非完全平行或垂直于阀体，或者不要在任何位置用手调整管接螺母。
Do not adjust the union nut with the handle in any position other than fully parallel or perpendicular to the body.
把调整器紧固在钢瓶上，安全地上紧入口螺母。
Fasten the regulator to the cylinder and tighten the inlet nut securely.
叶轮经过静平衡校验，用轴套和两侧的轴套螺母固定，其轴向位置可以通过轴套螺母进行调整。
The impeller is static balanced, and it is fixed with sleeve and nuts aside, its axial position can be adjusted by sleeve nut.
主要生产销售：螺母、螺丝、激光切割件、非标螺母、 调整间隙片、 激光切割加工、垫片、冲压件等各类产品。
The main products are as follows: various nuts, screws, gaskets, stampings and other types of non-standard products.
主要生产销售：螺母、螺丝、激光切割件、非标螺母、 调整间隙片、 激光切割加工、垫片、冲压件等各类产品。
The main products are as follows: various nuts, screws, gaskets, stampings and other types of non-standard products.
应用推荐