讨论了小型射流吸石泵系统的设计计算方法。
The design and calculation method of small jet stone pump system were discussed in this paper.
提出了使锁气阀处于最佳工作状态的设计计算方法。
An optimum design criteria to make the gas-lock valve in the best operation condition is proposed.
阐述了抽气止回阀的工作原理及气缸的设计计算方法。
Expound working principle of extraction check valves and the calculation methods of the cylinder design.
介绍了干线输气管道热连接分支管道的设计计算方法。
The method of design and calculation on in-line welding branch pipeline for gas transmission trunk line is introduced.
利用这种设计计算方法还可以预测曲柄销的失效概率。
This method can also be used to predict the failure probability of the crank pin.
举例说明了圆筒卡夹件和扭转杆卡夹件的设计计算方法。
The design methods of annular snap fits and torsional snap fits are illustrated.
与传统设计比较，本设计计算方法新颖、可靠、实用可行。
Compared with the traditional design, this approach is newer, more reliable, feasible and practical.
阐述了充水壅水橡胶坝的设计计算方法，提出了抗冰冻措施。
This paper discusses the design and calculation method of filling water rubber dam and also poses the freezing-proof measure.
本文详细介绍该设备的性能特点和设计计算方法，并附有算例。
We described in detail the performance characteristic and design calculating method of this equipment, the example of calculation attached.
本文叙述了用于SEM的低压运用电子枪的设计计算方法及结果。
The numerical calculation method and result of an low - voltage electron gun for SEM are described in this paper.
本文提出了一种新的纵向轴系游动端支座合理间隙设计计算方法。
The paper proposes a new calculation method for determining the reasonable gap in the bearing at free end of the longitudinal shafting.
该文具体介绍垫层厚度和宽度的设计计算方法以及垫层施工方法。
Practical design of thickness and with of the mattress and the method of construction are introduced in this paper.
本文介绍了几种常用的弹性测力计的设计计算方法，并附有计算实例。
The article introduces the design and calculating methods of elastic dynamometers for general use, with explanatory example.
重点阐述了无机械手自动换刀装置主要组成部分刀库的设计计算方法。
The designing and calculating methods of major component part tool magazine of no-finger automatic tool changer were expounded.
基于中试结果提出了部分废气循环的煤炭干燥系统及其设计计算方法。
According to the pilot test results, a new coal drying system with part exhaust gas circulation and its design method are put forward.
在理论研究和设计实践的基础上，提出了旋风分离器的设计计算方法。
Based on the theoretical researches and design practise, the design and calculation method of cyclone air separator was put forward.
本文重点论述了伞状折网架的设计计算方法，以及有关设计构造要点。
This paper presents the design methods and construction keys of umbrella folded space truss.
介绍绿地、花坛的构造、排水系统的类型以及排水系统的设计计算方法。
Also the design and calculation of their water drainage system are added.
介绍了角接触球轴承沟道直径的设计计算方法，并给出了相关的计算式。
Design calculating method of grooved raceway diameter of angular contact ball boring is introduced, and the related calculating formula is given.
本文提供了一种在常用方法基础上考虑土体结构性强度增长的设计计算方法。
In this article a new calculation method which take into account soil structure was provided based on common method.
文中阐述了该装置的结构特点和设计计算方法，分析了各因素对其承载能力的影响。
Factors that influence the device loading capacity are analyzed. The reasonability of the design method is testified by an actual high speed spindle's design.
脱硫吸收塔结构及荷载形式复杂，常规设计计算方法不能给出其应力和变形分布情况。
The structure and load form of the absorbing tower is complex and regular design and calculation method cannot give its distribution condition of the stress and deformation.
探讨了汽车分电器推板式离心提前机构的结构和工作过程，给出了它的设计计算方法。
This paper probes the structure and working process of auto distributor push off centred advance machine and its design calculation methods are given.
介绍了MCV 2520小型立式加工中心圆盘式刀库转动定位机构的设计计算方法。
The design and calculation method on rotating and locating mechanism of MCV2520 miniature vertical machining center's circular tool magazine are introduced.
论文提出的双柱联合浅基础和双柱联合桩基承台的设计计算方法可供工程设计人员参考。
Designers may refer to the design-calculation methods which are suggested in this thesis in terms of double-column combined shallow foundation and double-column combined pile caps.
因此，研究和探讨这类桥梁的受力行为和设计计算方法具有重要的理论意义和工程实用价值。
So it is significative and valuable to research and discuss structure behavior and calculate method of multi-box girder Bridges.
介绍两辊式和三辊式机械弯曲除锈原理，给出关键参数如辊子直径、牵引力等的设计计算方法。
Design and calculation method of the key parameter such as the diameter of roller and pulling force are given.
针对15.2(0.6口寸)钢绞线稳定化处理的加热要求介绍了其加热感应器的设计计算方法。
This paper introduces the method of the design and calculation of heating inductor for the treatment of the stabilization of 15.2 mm (0.6 inch) strand steel wire.
对振动流化床的基础研究资料进行分析和归纳，结合实际选型经验，提出振动流化床的设计计算方法。
Analyze and sort out basic research information of vibrating fluidized bed, put forward design calculation method of the vibrating fluidized bed.
对振动流化床的基础研究资料进行分析和归纳，结合实际选型经验，提出振动流化床的设计计算方法。
Analyze and sort out basic research information of vibrating fluidized bed, put forward design calculation method of the vibrating fluidized bed.
应用推荐