认为激光硬化处理能够有效地改善材料的表面硬度和耐磨性。
The laser hardening material can effectively improve the surface hardness and wear resistance.
摩擦学测试表明渗氮样品不仅摩擦系数大大降低了,而且表面硬度也获得了显著提高。
Tribological tests reveal that the friction coefficients of the nitrided samples are greatly reduced, and the surface hardness is remarkably improved at the same time.
结果表明,该钢经复合处理后,具有较好的表面硬度和良好的耐磨性,显著地增加了刀具的使用寿命。
The results showed that the steel after combined treatment had higher surface hardness and wear resistance, and prolonged the service life of cutting tool.
奥氏体不锈钢通过等离子氮碳共渗可显著提高其表面硬度,从而提高耐磨性而又不损害其抗腐蚀性能。
Hardness and consequently wear resistance of austenitic stainless steel can be highly increased, without loosing corrosion resistance by producing plasma nitrocarburizing surface layers.
磨削烧伤使表面硬度下降,磨损加剧。
The grinding burn causes the surface hardness falling off and wear speeding up.
干燥后,涂装物表面硬度提高,光洁亮丽。
After drying, the workpiece surface hardness will be increased, smooth and beautiful.
描述强度的一种最简单方法是以表面硬度来表示。
One simple way of describing strength is in terms of surface hardness.
磨削热导致回火引起淬硬钢磨削后表面硬度变化。
Tempering resulting from grinding heat caused surface hardness changes of hardened steels after grinding.
建议:泵轴或防护套的表面硬度要达到60hrc。
Suggestion: pump shaft or protective set of surface hardness to achieve 60hrc.
因此,辊子需要较高的表面硬度和较深的硬化层深度。
Thus, these rolls require a higher surface hardness and must be hardened to a greater depth.
分析了工厂网带炉条件下淬火织针表面硬度不足的原因。
Analyse the reason that surface hardness of quench needle is not enough under original production technology circumstance of factory.
局部淬火处理的齿轮具备比心部组织硬度高的表面硬度。
The case hardening process results in gears that have much harder surfaces than cores.
具有表面硬度高、耐候性好等特点,适用于制作宝丽板。
With high surface hardness and sound glossiness and weather resistance properties, these resins are suitable for the manufacture of polyester plywood.
离子注入后,尼龙6表面硬度提高与离子能量损失机制有关。
Surface hardness improvements of Nylon 6 implanted with ions were linked to mechanism of energy loss of ions.
在过去的20年里,一些工艺被引入用来提高钢的表面硬度。
During the past 20 years, several processes have been introduced to obtain enhanced surface hardness of steels.
磨削深度是影响工件表面硬度和磨削淬硬层厚度的主要因素。
The effect of grinding depth on work piece surface hardness and hardness layer depth is important factor.
电子束表面处理可以提高铝合金材料的表面硬度、增加耐磨性。
The surface hardness and wear resistance of aluminum alloy are both improved by means of scanning electron beam.
试件的表面硬度、 耐磨性和尺寸稳定性均有不同程度的提高。
The hardness and abrasive property of the surface, and the anti-shrink efficiency of the treated wood samples, were all improved.
低浓度氟化物溶液和氟泡沫处理后釉质的表面硬度无明显改变。
The microhardness values were not changed after treatment with other agents.
通过实验研究了巴克豪森噪声强度与铁磁材料表面硬度之间的关系。
The relationship between the surface hardness of ferromagnetic material and the intensity of Barkhausen noise was studied.
通过合并磨削热模型和回火效应可以预测工件磨削后的表面硬度变化。
Combining the tempering behavior with the grinding thermal model, the change in surface hardness due to grinding heat could be predicted.
另外,研究了消失模铸造法铸型表面硬度、界面换热系数的变化规律。
Moreover, the variation law of mold surface hardness and interface heat transfer coefficient were studied.
通过合并磨削热模型和回火效应,可以预测工件磨削后的表面硬度变化。
Combining the tempering behaviour with the thermal model of grinding, the change in surface hardness due to grinding heat can be predicted.
本文研究了离子注入对钢的表面硬度、光反射率和高温氧化性能的影响。
In this paper, we report on the modification of surface hardness, optical reflectivity, and high temperature oxidation behaviour of ion-implanted steel samples.
结果表明,激光硬化处理的表面能够有效地改善材料表面硬度和耐磨性。
The results show, surface treated by laser hardening can improve the surface hardness and wear resistance.
爪形和环形断裂由表面硬度偏高造成,并提出解决断裂问题的合理化建议。
Ungula and ring fracture are due to higher surface hardness. The rational suggestions to settle fracture are put forward.
土壤摩擦力还随固体表面光洁度降低而增加,随表面硬度增加而趋于减小。
The friction increases with the decrease in solid surface finish and tends to decrease with the increase in its surface hardness.
通过改变组分配比,研究水泡前后材料表面硬度的变化,筛选出最佳配方。
The surface hardness of the materials having different compositions before and after absorbing water was studied, and the best formula was determined.
考察了填充系数对力学性能的影响,包括表面硬度、冲击强度和弯曲强度。
The influence of filling coefficient on mechanical properties, including surface hardness, impact and flexural strength, are investigated.
在进行放电(电火花)加工后,表面硬度不会增高,可简化其后的加工工序。
Surface hardness will not be increased after the EDM process which simplifies the following machining procedures.
应用推荐