在表面进行涂层防护可减少表面氧化。
研究了加热工艺对含铜钢表面氧化的影响。
The effect of heating process on surface oxidation of copper-bearing steel was studied.
同时，表面氧化层减薄，脱落情况明显减少。
At the same time, the oxide scale thins out and flaking condition reduces evidently.
金铝圈表面氧化处理。
钛植入体的生物学性能取决于其表面氧化膜的表征。
The Biological properties of titanium implant depend on its surface oxide film.
必须进行粗加工以去除原材料轧制过程中的表面氧化脱碳。
Rough machining shall be performed so as to remove all mill decarburization from the raw material surface.
综述了镁及其合金的腐蚀原理和表面氧化技术的研究现状。
This review details the state of corrosion mechanism of the magnesium alloy and surface modification technologies applied to improve its corrosion and wear resistance.
发现表面氧化对铁损没有明显影响，内氧化层对铁损影响最大。
External oxidation layer didn't found to have obvious influence on iron loss, the largest influence came from internal oxidation.
由于表面氧化层的存在和内部冶金结合的形成，重熔层硬度较喷涂层高。
Microhardness of the remelting coating is higher than that of spraying coating because of oxide layer and metallurgical bonding.
结果表明金属铜在腐蚀达到稳态时其表面氧化膜具有一定的组成和厚度；
The theoretical results suggested that both the thickness and composition of the oxide film were definite after the electrode processes reached stable states.
不锈钢表面氧化皮成分及其与基体的界面结合强弱直接决定了酸洗的难易程度。
Composition of the oxide scale formed on the stainless steel surface and the bonding strength between the layer and substrate directly determines the difficulty of pickling.
研究了铝合金防伪花纹板材的生产工艺，花纹辊磨制方法，板材表面氧化工艺。
The production technics of aluminium alloy defending fake flower pattern sheet, grind technique of flower pattern roller and sheet oxidation technique are studied.
修饰与改性方法包括形成包敷层和金属层、表面氧化、机械研磨以及掺杂等方法。
The methods of modification included the surface covering of graphite with a layer of disorganized carbon or a film of appropriate metal, surface oxidation, mechanical grinding and doping.
但预热温度不宜过高，以免引起基体表面氧化而影响涂层与基体表面的结合强度。
However, the preheating temperature should not be too high, so as to avoid matrix effects of surface oxidation and surface coating and the substrate bonding strength.
工作辊表面氧化膜状态与带钢表面氧化铁皮细孔及小白条压入缺陷的产生有密切关系。
The defects of the needle-shaped hole and narrow white threads on the strip surface have close relationship with oxide film of work roll.
经表面氧化层处理后，焊料表面粗糙度的降低引起低剪切速率下焊膏粘度的明显升高。
After surface oxide film treatment, the increase of viscosities at low shear rates results from the decrease of surface roughness on the surface of solder powders.
为研究不同氧化层厚度对焊料性能的影响，开发出一种新的焊料表面氧化层减薄工艺。
A unique oxide thinning process is proposed in order to investigate the effect of oxide thickness on soldering properties.
通过测量循环伏安曲线，分析了两种矿物表面氧化形成的产物，元素硫是主要的疏水体。
Reaction products by the surface oxidation of two minerals were studied by measuring the cyclic voltammetric curves, where the elemental sulfur was the main hydrophobic entity.
采用化学腐蚀法，通过控制有机酸腐蚀后焊料烘干的氧分压和温度控制焊料表面氧化层厚度。
Chemical removal approach is utilized and the oxide thickness is controlled by controlling the oxygen pressure and temperature during solder drying after organic acid removal.
加热炉的生产目的是满足轧制要求的钢坯温度分布，并实现钢坯表面氧化烧损最少和能耗最小。
The purpose of reheat furnace production is to acquire the slab temperature distribution rolling required, and achieve the fewest stock scale loss and energy consumption.
通过该方法，能够有效且充分地洗掉附着在实施表面氧化处理的热镀锌钢板的表面的酸性溶液。
By this method, an acidic solution adhered to the surface of the hot-dip galvanized steel sheet after the surface oxidation treatment can be efficiently and sufficiently washed out.
绘制了氧化动力学曲线，用带能谱分析的扫描电镜观察了涂层的表面氧化形貌和横截面组织形貌。
The oxidation kinetics curve was drawn. The surface morphology and cross section micrograph of the Al-Si coating were studied by using SEM.
同时，清除黄铜矿表面氧化溶解产物——单体硫后，有助于离子扩散和黄铜矿的进一步氧化溶解。
Meanwhile, the removal of the free sulfur from the chalcopyrite will facilitate the ion diffusion and the further oxidative solution of chalcopyrite.
其中钕铁硼磁钢化学稳定性较差，在磁滚筒内潮湿的空气中，易出现表面氧化逐步分层剥落的现象。
One ndfeb magnets chemical stability is poorer, in magnetic drum in humid air, easy appear on surface oxidation gradually layered peeling phenomenon.
结果表明，采用瓷介质与铁介质磨矿时，方铅矿表面形态、表面氧化产物及浮选行为存在明显差异。
The results show that there exist great differences in surface morphology, oxidation species and flotation behavior of galena ground with ceramic or iron media.
我们采用了用于航空航天钛合金制品的表面防护技术，有效地防止了钛合金在高温条件下的表面氧化！
We use titanium alloys for aerospace products, surface protection technology, which effectively keep the titanium alloy from being oxidized at high temperature.
概述了穿孔顶头表面氧化膜的形成、结构、性质、作用，在穿孔过程中的变化及其对顶头使用寿命的影响。
This review focuses on various aspects of piercing plug surface oxide film, including formation, compose, property, effect, transformation in the piercing course and the influence of plug's life.
改造后使加热炉提高了加热能力和加热质量，减少了板坯表面氧化烧损，降低了煤气消耗，经济效益显著。
As a result, the heating capacity and quality of heating furnace is improved, the slab surface oxidation burning loss is decreased and the gas consumption reduced and the economic benefit remarkable.
本文通过理论分析，结合实验室研究与现场生产，对YL112铝合金材料表面氧化处理工艺进行了研究。
In this thesis, by combining laboratory research, field production and theoretical analyze we have studied superficial oxide treatment technology to YL112 aluminum alloy material.
本文通过理论分析，结合实验室研究与现场生产，对YL112铝合金材料表面氧化处理工艺进行了研究。
In this thesis, by combining laboratory research, field production and theoretical analyze we have studied superficial oxide treatment technology to YL112 aluminum alloy material.
应用推荐