然后阀瓣螺栓紧固在关闭位置。
将底板用螺栓紧固到风机桥架的刚件上。
该螺栓紧固装置不易磨损变形打滑、防盗性能好。
The bolt clamp device is not easy to wear, deform and skid and has good anti-theft performance.
采用活接螺栓紧固，能快速开启，便于安装于维护；
Using live after bolts, can rapid opening, installation convenient in maintenance.
采用活节螺栓紧固，能快速开启，便于安装与维护。
Fastened with eyelet bolt, it can be turned on quickly, installed and maintained conveniently.
采用活结螺栓紧固，能快速开启，便于安装与维护；
Fastend with eyelet, it can be turned on quickly, installed and maintained conveniently.
介绍了电动螺栓紧固机-单片机控制装置的开发与设计。
This paper mainly discusses the design and development of the intelligent controlling system that is used in screw tightening.
介绍了轴端螺栓紧固装置的设计方案、主要技术参数和性能特点。
Described are the design scheme, main technical parameters and performance features of the tightening device for bolts at the axle ends.
铲斗底板上安装有耐磨衬板，由螺栓紧固可更换，布氏硬度为500。
Replaceable bolt-on wear plates on bucket floor, 500 Brinell.
特征是包括飞轮、塑料风叶轮，塑料风叶轮用螺栓紧固在飞轮的螺孔上。
The invention is characterized in that the invention includes a flywheel and a plastic fan blade which is tightly fixed on the screw hole of the flywheel by a bolt.
接线搭接面确保清洁，涂抹导电膏，螺栓紧固力矩符合设备接线要求说明。
The junction of bonding jumper should be clean and covered with conductive paste. And the tightening moment for bolt must fit with equipment wiring requirements.
论文对超声螺栓应力测量原理，超声螺栓紧固力测试仪设计进行了系统研究。
The thesis lucubrated the principle of ultrasonic bolt tension measurement and design of ultrasonic bolt tension measurement instrument.
如果气体或所处理的流体泄漏，则建议以每次50英尺磅的增量增加螺栓紧固扭矩值。
If air or process fluid leaks, increase the recommended torque in increments of 50 ft. lbs.
一般来说，气缸和气缸盖用螺栓紧固在一起，气缸与气缸盖之间用一薄垫圈确保密封良好。
Generally, the cylinder and the cylinder head bolt together with a thin gasket pressed between them to ensure a good seal.
如果泄露仅仅出现在法兰面密封上，进一步的螺栓紧固基本上并不会阻止法兰连接部分的泄漏。
If there is leakage at the flange face-seal only, further tightening of bolts will almost never stop any flange joint leak.
安全阀阀盖应该采用不锈钢螺栓紧固，应该采用四分之一转锁定连接来所定安全阀的弹簧负载。
The relief valve cover shall be secured with stainless steel bolts and shall utilize a quarter-turn locking joint to capture the spring load of the relief valve.
把两个管道、管件或器材，先各自固定在一个法兰盘上，两个法兰盘之间，加上法兰垫，用螺栓紧固在一起，完成了连接。
The two pipes, fittings or equipment, each first fixed in a flange on the flange between the two, together with flange pad, fastened together with bolts to complete the connection.
运转约15 - 30分钟之后，再次紧固螺栓直至泄漏达到允许范围。
After running about 15-30 minutes, again until the leak fastening bolt to reach permitted.
一旦开始紧固螺栓，要确保各个螺栓均匀受力。
Once fastening bolts, each bolt to ensure that the force evenly.
为了将橡胶套管法兰挤出来，需要按照星形模式重新紧固所有法兰螺栓。
Retighten all flange bolts in a star pattern in order to extrude rubber sleeve flange material.
如果台面索引轴松动，拧紧固定螺栓。
将地脚螺栓连接板用螺母紧固。
检查对其余为您的周期，并寻找螺丝，螺栓及其他紧固件。
Check over the remainder of your cycle and look for screws, bolts and other fastenings.
试车前务必检查所有螺栓、螺母是否有松动，若有松动的螺栓、螺母必须重新紧固。
Make sure check the bolt and nut before testing run. and if they become less crowded, fastening again.
破碎机停机时，要检查紧固螺栓是否牢固和易磨损部分的磨损程度，是否需要更换。
Crusher downtime, check whether firmly and tighten bolts of wear parts wear degree, whether to need replacing.
传感器要采用螺栓固定，保证一定的紧固力矩，长时间使用不会松动。
Sensor bolt to be used to ensure a certain degree of tightening torque, prolonged use will not become loose.
用螺纹联接并起紧固作用的零件称为螺纹紧固件。常用的螺纹紧固件有螺栓、双头螺柱、螺钉、螺母、垫圈等。
Parts with threads used for joining and fastening are called screw fasteners. The most widely used components as screw fasteners are bolts, double screw bolts, screws, nuts, washers.
检查各联接部件是否牢固，各螺栓是否紧固。
To test all kinds of the connection components is firm or not.
安装将悬吊横梁前部紧固到上控制臂下面的框架轨道的螺栓。
Install bolts holding front of suspension crossmember to frame rails under upper control arm.
安装将悬吊横梁前部紧固到上控制臂下面的框架轨道的螺栓。
Install bolts holding front of suspension crossmember to frame rails under upper control arm.
应用推荐