胶接剂看去象是一种液态蛋白质。
并对胶接方法和反应机理进行探讨。
This paper also discusses the method of adhesive bonding and the reaction mechanism.
本文介绍了翼身融合体无人机的胶接技术。
In this paper, the bonding technique for the blended wing body mini UAV is presented.
胶接工艺中，胶接接头的设计是一重要的环节。
In the glue processing, the design of the gluing joint is prerequisite and important.
并以胶接密封实例说明其工艺特点及应用意义。
Its charateristics and applications are illustratedby glued examples.
胶接能够提供连续的面连接，有利于减轻结构重量。
Adhesion can provide continuous joint which is useful to reduce the structure weight.
激光胶接焊接头的抗剥离力远大于胶接接头的抗剥离力。
The peel force of LWB joint is far greater than that of adhesive bonded joint.
微胶接技术非常适用于微机电系统产品的自动化装配过程。
Micro adhesive bonding technology shows great potential in the assembly of micro-electro-mechanical system (MEMS) products.
在复合材料胶接修补中，补片的尺寸对胶接强度的影响非常关键。
In adhesive bonding repair using composite patches, the size of patch has an obvious influence on bonding strength.
系列电热胶带硫化机，是输送机械胶带接头硫化胶接的专用设备。
Series electric belt vulcanizer, mechanical conveyor belt is the vulcanization bonding of specialized equipment.
兰姆波各模式在时频空间能量分布变化与胶接强度有较好的相关性。
The Lamb modes in the AU signals were analyzed using time-frequency method, and the energy variation of Lamb modes was correlated to the adhesive bond strength with good correlation.
胶接缺陷的平均识别率在80%以上，胶接强度的估计精度也令人满意。
The average reliability of defects classification is over 80%, and the estimation of adhesive strength is satisfactory.
本文介绍了提高复合材料胶接质量稳定性应注意的关键因素和解决方法。
The key factors and some solutions are introduced for improving the quality stability of composite adhesion.
胶铆连接集中了胶接的连续密封性能、耐疲劳性能和铆接的抗剥离性能。
Bond-riveted joint gathers the continuous sealing and anti-fatigue properties of adhesion and the anti-peeling properties of riveting.
本次试验研究的是集成材长度方向胶合时胶接方式对其力学性能的影响。
The experiment aimed at studying the impact that the glue method does to the strength properties when the laminated finger-jointed lumber is glued along its longitudinal.
研究了煤矿安全用复合式氧气瓶缠绕胶接体系中阻燃剂的筛选及阻燃机理。
Flame retardant selection and inflaming retarding principle are researched on winding cementing system of compound oxygen cylinder used for coal mine safe.
简要概述了界面结合力的类型以及木材胶接操作过程中胶合强度的形成过程。
The type of interfacial binding force was discussed in this paper, and formation process of bonding strength during wood gluing operation was also discussed.
应用声发射检测技术研究金属铝单搭接胶接结构的缺陷检测和强度估计问题。
The defect testing and strength estimating of metal to metal single step-lap adhesive bond structures are studied by means of acoustic emission (AE) technique.
试验结果表明：降低应力集中及剥离应力小的接头形式可有效地提高胶接强度。
The results show that the joint forms which have less stress, concentration and less peel stress can raise bonding strength greatly.
冷硫化胶接技术较之热硫化胶接技术具有工艺简单、操作方便、费用低廉等特点。
Compared with hot vulcanized gluing technique, cold vulcanized gluing technique features simpler process, easier operation and cheaper cost etc.
本文研究了三种常用酚醛型粘合剂胶接nbr -金属模压件的固化压力依赖性。
In this paper, the curing pressure dependence of NBR-me-tal bonding of three common phenolic adhesives were studied.
介绍皮带胶接新方法，解决了皮带热硫化胶接时间长、操作复杂、成本高的问题。
A new method of belt connection for solving the problem of long time, operating complication and high cost of hot vulcanization connect of belt.
文中叙述了胶接工艺应具备的条件，复合材料胶接连接工艺特点和质量控制等内容。
In this paper, basic requirement of adhesive technology and quality control of composite material adhesive bonded technology are discussed.
损伤金属飞机结构的复合材料补片胶接修理技术是一项经济而有效的结构延寿方法。
Bonded composite repair has been recognized as an efficient and economical method to extend the service life of damaged aircraft metallic structures.
本文简略叙述复合材料胶接的接头破坏形式，接头力学分析，接头设计及测试方法。
The failure form of joint, mechanical analysis of joint, joint design and test methods of adhesive bonding of composites are presented briefly in this paper.
第二、粘合胶接假山1、先要调好水泥浆，注意浆要随用随调，还要注意浆的稀稠度。
Second, 1, the first adhesive rockery to adjust the cement slurry, slurry to be in tune with the attention, but also pay attention to dilute pulp consistency.
分析了皮带胶接头损坏的原因，研究制定了合理的皮带胶接工艺，取得了良好使用效果。
This treatise analyzes the causes of damage in belt glued ends, studies and works out rational belt glueing technics, showing fine results.
以此特征频带的小波变换系数作为声-超声信号特征参数，可分辨出胶接区域的缺陷信号。
The wavelet coefficient of the feature band was regarded as the feature parameter of the Acousto Ultrasonic signal and it can distinguish defects from the adhesively bonded joints.
以此特征频带的小波变换系数作为声-超声信号特征参数，可分辨出胶接区域的缺陷信号。
The wavelet coefficient of the feature band was regarded as the feature parameter of the Acousto Ultrasonic signal and it can distinguish defects from the adhesively bonded joints.
应用推荐