证明了其聚合反应为游离基机理。
A free radical mechanism for acrylonitrile polymerization was proposed.
而脉冲宽度对聚合反应的影响不大。
聚合反应温度提高，聚合速率加快。
Polymerization speed increases with the increase of reaction temperature.
有两种类型的聚合反应：加成和缩合。
There are two types of polymerization reactions: addition and condensation.
还讨论了溶剂极性对聚合反应的影响。
研究了该聚合反应的特征及动力学行为。
Some features and the kinetic behavior of the polymerization have been investigated.
此方法适用于有机聚合反应过程中钠的测定。
This method can be applied to determine sodium in organic polyreaction.
探讨了聚合反应机理。
阐明了聚合反应对搅拌装置的要求及设计要点。
Requirements and key design points of polymerization for mixing unit were clarified.
本文研究了脂肪醇聚氧乙烯醚的聚合反应动力学。
The kinetics of polymerization of alcohol polyoxyethylene ether is studied in this paper.
并对聚合物的结构及聚合反应的类型进行了探讨。
The structure and polymerization reaction type of the polymer were also discussed.
聚合反应和啤酒糖化生产过程是常见的典型间歇生产过程。
Polymerization saccharification and beer production process is often the typical batch process.
讨论了催化剂、 引发剂、聚合反应温度对产物的影响。
The effects of catalyst, initiator and reaction temperature on the product were discussed in detail.
并提出了该体系进行阴离子乳液聚合反应可能的反应历程。
The possible polymerization mechanism causing anion emulsion polymerization by this system is raised.
环保型的印刷油墨连接料是通过植物油的热聚合反应获得。
The vehicle of environment friendly printing ink can be produced by the heat polymerization of plant oils.
进行了过氧化物酶催化木质素与酚聚合反应及其动力学实验研究。
The copolymerization reaction and its kinetics of lignin and phenol with peroxidase as catalyst were researched.
介绍了化工间歇聚合反应过程辨识与控制软件包的设计原理和设计方法。
The principle and method of design for recognition and control software package for chemical polyreaction process are presented.
在此基础上，提出了PA 6聚合反应工程研究中尚有待开展的几点建议。
And then, a few problems for the further research in PA6 polymerization process are pointed out.
这些结果说明了界面聚合反应的规律和生成膜的分离性能的变化规律基本一致。
These results proved that there were some interrelation between the rules of interfacial polymerization and the performance of membranes.
此外探讨了聚合反应条件对树脂吸油率和吸油速率的影响以及树脂的缓释性能。
The influences of reaction conditions on oil absorbency and swelling rate were studied, as well as slow release property.
水相聚合反应催化剂的研究今后将会成为聚烯烃催化剂研究的一个重要组成部分。
The researches on aqueous phase polymerization catalyst could constitute an important part of the future development of polyolefin catalysts.
研究了影响XTBN的组成、分子量和微观结构，以及聚合反应速率的主要因素。
The essential factors which affect the composition, molecular weight, microstructure and the rate of polymerization of XTBN were studied.
分子基态与电荷转移态的电荷转移过程定性地解释了双光子聚合反应的聚合机理。
The charge_transfer process for the charge_transfer states is displayed, and then the mechanism of photopolymerization is discussed qualitatively.
探讨了乳化剂种类、乳化剂用量、单体组成等因素对聚合反应及胶粘剂性能的影响。
Affect of sort and dosage of emulsifier, composition of monomers on the polymerization and the adhesion properties were discussed.
乳化剂、引发剂用量及反应温度、反应时间和搅拌速度对乳液聚合反应有重要影响。
The emulsion polymerization also was influenced by the dosage of emulsifier and initiator, reaction temperature and reaction time and agitating speed.
叙述了裂解气压缩机内的聚合反应、避免方法。简要地指出了注水系统设计中的要求。
The aggregation reaction in crack gas compressor is described. The requirement of water inject system design is briefly pointed out.
本研究还考察了半连续聚合反应进程中苯丙树脂分子量和分子量分布指数的变化规律。
The changes in the molecular weight and molecular weight distribution index of the resin during the semi-continuous polymerization were also researched.
探讨了单体浓度、反应温度、引发剂用量等因素对聚合反应速率和产物特性黏数的影响。
The effects of monomer concentration, reaction temperature, initiator dosage on polymerization rate and intrinsic viscosity of product were investigated.
重点描述了聚合反应挤出设备的类型与特点，进而介绍了聚合反应挤出设备的应用概况。
The type and characteristics of the equipments in reactive extrusion processes for polymerization were mainly described, and then its application was introduced briefly.
重点描述了聚合反应挤出设备的类型与特点，进而介绍了聚合反应挤出设备的应用概况。
The type and characteristics of the equipments in reactive extrusion processes for polymerization were mainly described, and then its application was introduced briefly.
应用推荐