筒体利用端盖支承在主轴承上。
端盖将被用来作为轴承或旋转点。
端盖准确地从精密加工方钢块。
End caps are accurately machined from precision square steel blocks.
电镀锌端盖及骨架，不易生锈。
Zinc plated cap and center frame, good rust prevention performance.
将末端端盖和保险杆分隔开。
安装连接末端端盖到前挡泥板的螺栓。
Install the bolts attaching the end cap to the front fender.
端盖要么髹黑漆标准或黑色环氧漆涂。
End caps are either painted with standard black paint or painted with black epoxy paint.
端盖-铝端盖提供坚固耐用。
End caps - Aluminum end caps provide sturdiness and durability.
端盖从加工精度准确方钢块。
End caps are accurately machined from precision square steel blocks.
仔细地检查漏水孔端盖与端座水的渗出量。
Carefully check the amount of water seepage from the end cap and end bell weep hole.
拆去连接末端端盖前面到部分板下侧的螺丝。
Install the bolts attaching the end cap to the front fender.
在扣件尾部和保险杆边缘外部定位末端端盖。
Position the end cap on the rear of the retainer and the outer edge of the bumper.
全面分析了减震器储油缸两端端盖的焊接特点。
The welding characteristics on the double end cover of deoscillator stock tank are analyzed all-sidedly.
本设计阐述了制造“轴封端盖”的复合模的设计。
This design elaborated the manufacture "the axis seals the end cover" compound mold design.
端盖用螺栓将它们固定在管板上并加入垫片密封。
Cover is fixing on the tube plate with some sealed gasket by bolt.
我有一些平板端盖焊接起来用腿和模具材料的淤塞。
I had some flat plate end caps welded up to use as legs and mold material blockages.
我想，即使作出修改的大会，将取代压载水舱端盖。
I think I would even make a modified assembly that would replace the ballast tank end cap.
世贸中心，其中被列入，但也有两个橡胶O型圈为端盖。
The WTC which was included, there were also two rubber O-rings for the end caps.
阀体和内部零件：阳极电镀铝合金、铜。加固端盖：塑料。
Valve body and internal parts: anodized aluminum alloy, copper. Reinforcement Cover: Plastic.
阀体和内部零件：阳极电镀铝合金、铜。加固端盖：塑料。
Valve body and internal parts: anodized aluminum alloy, copper.
建立了针对柱形真空杜瓦容器端盖密封结构的轴对称模型。
An axial symmetrical model is set up for the sealing structure of the bulkhead plate for a columniform dewar.
在分析端盖零件压铸工艺的基础上，论述了压铸模的设计要点。
Based on analyzing die casting process of cover part, the authors discuss the main points of the design of die casting mould.
在设计过程采用锥面制动端盖实现了工作状态和制动状态的互锁。
In the design process using cone brake cover state and work to achieve a state of interlocking brake.
为了承受高负荷，如在实际情况下，固体铸铁轴承端盖投入使用。
In order to withstand high loads, as is found in practical circumstances, solid cast iron bearing end shields come into use.
本加热器是常用的管壳式换热设备，由端盖、壳体、管组和附件组成。
The heater is a kind of used shell- and-tube heat exchanger which consists of head cover, Shell, nest of tubes and accessories.
原木质地的建造材料和抛光金属端盖使建筑的“棱形形式”显得并不突兀。
The structure's "prismatic form" is softened by the texture of the raw wood, along with end caps made of polished metal.
为提高探测器的接收度，EMC在先前桶部设计的基础上增加了端盖部分。
The end-cap EMC has been recently designed as a supplement to the previous barrel part in order to increase the acceptance.
为提高探测器的接收度，EMC在先前桶部设计的基础上增加了端盖部分。
The end-cap EMC has been recently designed as a supplement to the previous barrel part in order to increase the acceptance.
应用推荐