对所设计的销-盘磨损试验机进行了反复改进。
用环块磨损试验机进行了磨损试验，并进行了腐蚀试验。
The wear tests with ring on block wear test machine and corrosion tests were carried out.
低应力冲刷磨损的测试是在混砂盘及橡胶轮两种磨损试验机进行。
Low stress erosion wear tests were done in sand mixing pan and rubber wheel wear testing machine.
根据链条铰链磨损机理，提出对链条快速磨损试验机的设计要求。
According to the chain hinge wear mechanism, this paper advances the design requirements of the high speed wear testing machine of chain.
利用球盘磨损试验机和电化学综合测试仪研究了IBED膜层的摩擦学性能和电化学腐蚀特性。
The wear resistance and electrochemical corrosion properties of IBED coatings were investigated with ball-on-disk wear tester and electrochemical equipment, respectively.
利用电子探针、磨损试验机等试验手段，研究了微量元素对特殊黄铜的组织和耐磨性能的影响。
Effect of microelement on the microstructure and wear resistance property of special brass have been investigated by SEM, abrasion machine etc.
采用M CF - 30型冲蚀磨损试验机对两种不同热处理后的低铬铸铁进行冲蚀磨损实验。
Erosion wear experiments were done for low-chromium cast iron containing nickel with two different heat treatments by MCF-30 erosion test machine.
利用金相显微镜、X射线衍射仪、电子探针及滑动磨损试验机，研究了合金熔覆层的显微组织及性能。
The microstructure and properties of the composite coatings were investigated by optical microscopy, X-ray diffractometer, electron probe microanalyzer and a skimming wear machine.
通过对M L-100磨粒磨损试验机测试，发现环氧树脂涂层的耐磨性与陶瓷粉末的粒度与含量有密切关系。
Wear resistance tests have proved that the wearability of epoxy. Bonding coating is firmly connected with the size and weight of ceramic powders.
通过自制的冲击腐蚀磨损试验机，施加不同极化电位对高锰钢在矿浆介质中的冲击腐蚀磨损行为进行了试验研究。
Effect of polarization potential on the corrosion-wear behavior of high manganese steel in ore slurry was investigated by a self-made impact corrosive-wear tester.
利用自行开发研制的DTW- 166热磨损试验机，研究了高铬铸铁、高速钢轧辊的磨损量与工艺参数的关系。
The wear characteristics of high chromium and high speed steel rolls are investigated with the DTW-166 thermal wear testing machine developed by us.
应用对滚圆盘磨损试验机研究了合金铸铁经激光熔融处理后的耐磨性，试验结果指出，激光处理试样的磨损失重大为减少。
The roll disk wearing testing machine is used to study the wearability of alloy cast iron after laser melting. The test result shows that the wear weightlessness is reduced greatly.
通过优化螺杆组合，研究了CFRPA复合材料中碳纤维的长度分布对其力学性能的影响，用MM—200磨损试验机测试了CFRPA复合材料的磨损性能。
The effect of carbon fiber length distribution in the composite on its mechanical properties by optimizing screw assemble is studied and the wear behaviors are tested on a MM200 wear machine.
采用TE66试验机对新型TAMZ钛合金的微磨粒磨损行为进行了研究。
The micro-scale abrasive wear behaviors of TAMZ alloy were studied using a TE66 micro-scale abrasion tester.
采用TE66试验机对新型TAMZ钛合金的微磨粒磨损行为进行了研究。
The micro-scale abrasive wear behaviors of TAMZ alloy were studied using a TE66 micro-scale abrasion tester.
应用推荐