介绍了碳弧气刨的工作原理和组成结构。
This paper briefly introduces the work principle and structure of carbon arc air gouging.
它也适用于直径达10毫米的碳棒进行碳弧气刨。
It is also suitable for carbon arc gouging using up to 10mm diameter carbon electrodes.
在碳弧前面放一个滤光片就可以得到令人满意的近单色光。
A satisfactory approximation to monochromatic light can be obtained with a filter placed in front of the arc.
开始后续焊接前，所有碳弧气刨面区域应接地至洁净明亮的金属。
All carbon arc gouged surface areas shall be ground to clean bright metal prior to subsequent welding.
本文报导了用直流碳弧放电方法制备的多层碳纳米管的拉曼光谱。
We present a Raman scattering study of multi wall carbon nanotubes prepared by DC arc discharge method.
数控电熔爆机床可在某些加工场合取代金刚石砂轮磨削、碳弧气刨加工。
EMEM may replace emery wheel grinding, carbon arc gouging operation in certain applications.
它能提供多种高性能的焊接模式，如恒压埋弧焊、恒流埋弧焊、气保焊、碳弧气刨。
It can provide several high performance welding modes, such as constant-voltage submerged arc welding, constant-current submerged arc welding, gas shielded welding and carbon arc air gouging.
公司具备电焊、二氧化碳气体保护焊、氩弧焊、碳弧气刨、氧气切割等特种作业人员。
Companies with welding, carbon dioxide gas shielded arc welding, argon, carbon arc gouging, oxygen cutting and other special operations personnel.
采用交流碳弧法高效合成碳包碳化铁纳米晶磁性微粉，磁性微粉产率达90 %以上。
A highly effective method for preparation of carbon-coated iron carbide nanocrystals by AC carbon arc discharge was studied, the yield of magnetic micro powder was over 90%.
红外线：从碳弧灯或氙弧发出的不可见的、长波长的辐射，它对胶片和设备传送热量。
Infrared: Nonvisible, long wavelength radiation from a carbon or xenon arc that contributes to the heating of the film and equipment.
研制的ZX5一800D电源在进行钨极氩弧焊、手工电弧焊、碳弧气刨及埋弧焊时均获得满意的性能。
The developed welding power source ZX5-800Dshows a satisfactory performance in the welding process of TIG. Shield metal arc, submerged arc and the. carbon arc air gouging.
研制的ZX5一800D电源在进行钨极氩弧焊、手工电弧焊、碳弧气刨及埋弧焊时均获得满意的性能。
The developed welding power source ZX5-800Dshows a satisfactory performance in the welding process of TIG. Shield metal arc, submerged arc and the. carbon arc …
研制的ZX5一800D电源在进行钨极氩弧焊、手工电弧焊、碳弧气刨及埋弧焊时均获得满意的性能。
The developed welding power source ZX5-800Dshows a satisfactory performance in the welding process of TIG. Shield metal arc, submerged arc and the…
焊接方法采用碳弧焊，通过生产实践验证是可行的，用户在使用中对产品的反馈论证了其焊接质量的可靠性。
The method of Carbon arc-welding is adopted. It is feasible in practice to be used in the material weld. The feedback from the user demonstrates the reliability of welding quality.
系统分析了太阳近紫外能量累积值与紫外能谱实测结果及实测阳光碳弧、紫外碳弧、氙灯等人工光源紫外能谱分布图；
The accumulated solar UV data, solar UV-spectrum in Guangzhou area, and UV-spectrum of artificial lamp as sunshine carbon arc, UV carbon arc, xenon arc etc were analyzed.
系统分析了太阳近紫外能量累积值与紫外能谱实测结果及实测阳光碳弧、紫外碳弧、氙灯等人工光源紫外能谱分布图；
This article describes that we tested Solar UV accumulated data, Solar UV-spectrum in Guangzhou area and UV-spectrum of artificial lamp as sunshine carbon arc, UV carbon arc, xenon arc etc;
结果表明，清根方式对焊缝冲击韧度有明显影响，用碳弧气刨清根得到的焊缝冲击韧度最好，而用酸性衬垫得到的焊缝冲击韧度最差。
It was found that impact toughness of weld metal was maximum using carbon arc air gouging, and it was minimum using acid backing.
通过对13 -5型马氏体不锈钢焊接接头进行等离子弧清根及碳弧气刨清根的比较，证明等离子弧清根对全焊透焊缝实施背面清根是可行的。
By comparing backgouging of plasma arc with carbon arc to the welded joint of 13-5 martensitic stainless steel, the backgouging of plasma arc is proved feasible for the full penetration weld.
可根据冶炼钢种，炉子大小及设备条件，分别选用配料加焦、喷碳、富氧、长弧法或全程喷碳、富氧、长弧法。
The following two methods can be chosen according to the steel sorts to be melted, furnace sizes and other equipment conditions. One is carbon powder and coke injection, with rich-oxygen injection an…
可根据冶炼钢种，炉子大小及设备条件，分别选用配料加焦、喷碳、富氧、长弧法或全程喷碳、富氧、长弧法。
The following two methods can be chosen according to the steel sorts to be melted, furnace sizes and other equipment conditions. One is carbon powder and coke injection, with rich-oxygen injection an…
应用推荐