给出了调制畸变的实验结果。
The experimental results of modulation pattern effects are given.
而畸变的负荷电流引起整个系统中母线电压畸变。
The distorted load current then causes distorted bus voltages to appear throughout the system.
CCD图像产生严重畸变的原因正是使用了滤光片。
The main reason causing serious distortion of CCD images is using filter.
我们将详细讨论耦合模公式对标量波导畸变的应用。
We discuss in more detail the application of the coupled mode formulas to scalar waveguide deformations.
当通过一个特殊镜头放映时，受到畸变的图象又重新展开。
When shown through a special lens the distorted picture spreads out again .
论述了电子束扫描正交图形簇产生畸变的非线性校正过程。
The process of nonlinear distortion correction of orthogonal pattern group in E-beam scanning is introduced.
在没有光学畸变的情况下，要使如此小的空间显的宽敞需要合适的设备。
Making such a small space look spacious without optical distortion requires the right equipment.
任何补偿这类初始脉冲畸变的处理，都能改善反射波的质量。
Any process that will compensate for such distortions of the initial pulse should improve reflection quality.
本文提出了一种基于空间一组平行线标定镜头畸变的简便方法。
A new approach for lens distortion calibration is presented in this paper, which utilizes parallel lines.
变异的倾向于偏离，如从一个正常的或被承认了的类型；畸变的。
Tending to deviate, as from a normal or recognized type; aberrant.
鉴于银行业务要求，相机畸变的标定方法必须具有快速、可靠的特点。
In view of the demands of bank operation, calibration algorithm of camera distortion must be quick and reliable.
建立了相机畸变的数学模型，并通过迭代优化算法估计相机的畸变参数。
The camera distortion model is builded and the distortion parameters can be estimated by iterative optimal algorithm.
随后又介绍了导致运动图像模糊及几何畸变的原因及对应消除模糊的方法。
Introduced the causes of motion image blurring and geometric distortion and the methods to deblur.
本文对影响齿轮热处理畸变的材料、锻造、预备热处理等因素进行了研究。
In this paper, the effect factors on heat treatment distortion, such as material, forging and preheat treatment etc. have been studied.
结果表明，半导体光放大器的载流子寿命是导致输出波形畸变的主要因素。
The results show that the SOA carrier lifetime is the main factor that produces converted waveform distortion.
当指引被给予时我们也许还会猜疑自己的指引，这是我们模板畸变的一个后果。
It is a result of the distortions in our template that we might second guess our own guidance when it is given.
首先有一个快速入门的透镜板，并让他们跟踪，包括重新将镜头畸变的工作流。
First off there is a quick introduction to de-lensing the plates, and getting them tracked, including a workflow for re-applying the lens distortion.
有染色体数目畸变的恶性肿瘤患者，无论临床转移或病理分级恶性程度都较高。
In the patients with malignant neoplasms, exitsmce of chromosome aberration predicted highly malignant in terms of cither clinical metastasis or pathological grading.
微区分析发现畸变的共晶奥氏体组织与球墨铸铁低韧性之间存在着直接的对应关系。
The analysis of micro zone discovers that there are directly relationships between the distortion structure of eutectic austenitic and lower ductility.
与均匀的压力分布比较起来，畸变的或真实的压力场对发动性能具有相当大的影响。
Relative to uniform inlet pressure, the distorted or actual profiles may have a rather profound effect on engine performance.
利用信号恢复技术，对地震式低频振动传感器因频率特性而畸变的输出作补偿处理。
Signal recovery technique is adopted to compensate the output which is distorted because of the frequency characteristics of seismic transducer.
组合影响系数表示发动机抗组合畸变的能力以及压力畸变和温度畸变之间的相互影响。
Combined effective coefficient shows engine's capability to resist the combined distortion and the interaction between pressure and temperature distortions.
在大量试验的基础上，深入分析并研究了马氏体不锈钢活塞环渗氮畸变的各项影响因素。
Various influence factors were analyzed in detail on nitriding distortion of the piston rings made of martensitic stainless steel based on abundant researches.
在吊舱进气道进口安装扰流板进行试验，研究扰流板进气畸变的影响因素及总压畸变特征。
Characteristics and influence factors of total pressure distortion are studied based on tests conducted on a disturbed board installed in the nacelle inlet.
此值控制着畸变的量。负数值校正镜头圆桶状面性畸变，而整数值校正镜头针尖状点性畸变。
This value controls the amount of distortion. Negative values correct lens barrel distortion, while positive values correct lens pincushion distortion.
根据硬齿面齿轮生产现状，分析了影响渗碳淬火齿轮畸变的因素，并提出了减小畸变的措施。
The factors that influence the distortion of carburizing and hardening gears were listed and several measures to reduce heat treatment distortion were proposed.
根据硬齿面齿轮生产现状，分析了影响渗碳淬火齿轮畸变的因素，并提出了减小畸变的措施。
The factors that influence the distortion of carburizing and hardening gears were listed and several measures to reduce heat treatment distortion were proposed.
应用推荐