爱迪生不是第一个想到用电照明的人;许多年来,笨重的电弧灯就在公共区域和工厂投入使用。
Edison was not the first person to have thought of using electricity for illumination: cumbersome electric arc-lighting had been employed in public Spaces and factories for a number of years.
在公司创建后的两年里,联邦电报公司为美国海军建立了一系列连接旧金山和夏威夷的电弧发射机。
Within a couple of years of its founding, Federal had crafted for the Navy a chain of arc transmitters linking San Francisco with Hawaii.
如果在继电器中发现可燃气体,这说明有内部故障,比如过热或者电弧作用;而继电器内的空气只说明油位低或者有漏油。
Flammable gas found in the relay indicates some internal fault such as overheating or arcing, whereas air found in the relay may only indicate low oil level or a leak.
一个容量180吨的电弧炉正在建设中,它一年将生产一百三十万吨钢铁,有600个工人在这里工作,它将落成于2012年的春天。
One arc furnace with capacity of 180 tons is under construction now.It will produce 1 million 300 thousand tons of steel a year. 600 employees are working here.It will be launched in spring 2012.
他们的炼炉不是那种爆发出阵阵轰鸣声的炼炉,相反,它们是使用小型的、低噪音的、利用电流来重新融化钢铁的真空电弧熔铸炉。
Its furnacesare not of the roaring blast variety; they are small, purring vacuum-arc furnaces that use electrical currentto re-melt steel.
电弧焊的焊条是由焊芯和药皮两个部分组成的。
Electrode for arc welding consists of the core and the coat.
本文介绍我国第一套炼锡电弧炉微机控制系统。
This paper introduces the first microcomputer Control system of arc furnace for tin smelting in China.
手工电弧焊通常是指采用药皮焊条的手工焊接法。
The manual arc welding normally refers to the manual welding using coated electrode.
介绍了一种新型的激光—电弧复合热源焊接技术。
In this paper, a new welding technique using compounded heat sources of arc and laser is introduced.
电弧电压:一般认为电源正常输出电压即为切割电压。
Four, arc voltage: generally believe that the power supply is normal output voltage for cutting voltage.
电弧炉炼钢是用来生产特殊钢和高合金钢的主要方法。
The electric arc furnace (EAF) steelmaking is the main method used to produce special steel and alloy steel.
焊接是一个涉及电弧物理、传热、冶金和力学的复杂过程。
Welding is a complicated process in which arc physics, heat transfer, metallurgy and mechanics are involved.
在脉冲真空电弧离子镀膜过程中,膜层厚度的控制至关重要。
Its very important to control the thickness of the film in the process of the pulsed vacuum arc deposition (PVAD).
本研究工作对水下焊接电弧物理及焊接冶金的研究有参考价值。
This research is significant and valuable to the study of underwater welding arc physics.
属于拉弧式电弧螺柱焊焊枪,焊接质量好,重量轻,操作方便。
Draw arc stud welding gun makes high welding quality, with light weight and convenient operation.
电弧炉炼钢可以分为以下4个阶段:装料,熔化,精炼和出钢。
The electric arc steelmaking process may be divided into the following four stages: charging, melting, refining and tapping.
如果气隙太小,当触点开路时就会形成电弧,并且电流继续流通。
If the gap is too small, an arc may develop when the contacts open and current continues to flow.
交流(ac)信号产生的电弧通常在电压通过零点时就会自己熄灭。
An arc due to an AC signal usually quenches itself as soon as the voltage level passes through zero.
电弧:高压切换产生的RFI(射频干扰)可能会干扰高速逻辑电路。
Arcing: The RFI (radio frequency interference) generated by high voltage switching may disrupt high speed logic circuits.
切割电弧稳定,切割速度快,切口平滑,变形小,挂渣少,节省材料。
Steady arc and fast cutting, even cuts, little deformation and slag, material-saving.
将电弧焊设备上的接地连接尽可能近地连接到将要焊接零件的焊接点上。
Connect the ground connection of the electric arc welding equipment as near as possible to the welding point on the part to be welded.
本文利用等离子体光谱诊断法对水下焊接电弧温度进行了比较系统的研究。
In this paper the temperature of underwater welding arc is investigated systematically by means of spectral diagnostics of plasma.
采用模糊控制技术,实现了电弧电压或短路频率的控制,提高了焊接质量。
Fuzzy control tests of arc voltage and short-circuit frequency are conducted to improve welding quality.
回收再利用也将推动电弧炉技术的进一步完善和薄板坯连铸技术的广泛采用。
It will also foster the further perfection of EAF technology and the ubiquitous use of Thin Slab Casting.
等离子电弧加热弯曲成形还可以降低机械加工引起的残余应力,有效减少回弹。
The plasma arc forming can also decrease the residual stresses caused in the mechanical processes, which can be of great significance in preventing rebounding.
如果切换电流太高,造成的温度升高和接触电弧将会劣化继电器并缩短接触寿命。
If the switched current is too high, the resulting temperature increase and contact arcing will degrade the relay and shorten the contact life.
如果切换电流太高,造成的温度升高和接触电弧将会劣化继电器并缩短接触寿命。
If the switched current is too high, the resulting temperature increase and contact arcing will degrade the relay and shorten the contact life.
应用推荐