计算的重点放在壁面热流率的预测。
The emphasis is placed on the predictions of the heat transfer rate on the wall.
试验给出机身对称面、翼前缘、立尾前缘等处的热流率分布。
The heat flux distribution is provided at the asymmetric side of the body, wing and the vertical fin.
实验结果表明，沸腾时，“界面汽化热阱”效应随热流率的提高而显著增大。
The experimental results show that in the pool nucleate boiling process the "effect of interfacial vaporization heat sink" obviously increases with the heat transfer flux.
用铂膜电阻温度计测量了前向台阶诱导激波与湍流边界层相互作用流场中的表面热流率脉动。
Wall heat transfer fluctuations have been measured using a platinum film resistance thermometer in forward facing steps induced shock wave and turbulent boundary layer interaction fields.
只有基于再附峰值热流率位置长度的参考温度条件下的雷诺数足够低，相互作用过程才能是纯层流的。
The process doesn't exhibit fully laminar unless the reference Reynolds number based on the location of peak heat transfer on compression ramp is low enough.
登革热流行期间，未曾接触病毒者中的感染率通常为40%至50%，但在最糟的情况下可高达80%至90%。
During epidemics of dengue, infection rates among those who have not been previously exposed to the virus are often between 40% and 50%, but could reach 80% to 90% in worse case scenario.
登革热流行期间，未曾接触病毒者的感染率通常为40%至50%，但可高达80%至90%。
During epidemics of dengue, infection rates among those who have not been previously exposed to the virus are often 40% to 50%, but can reach 80% to 90%.
分析了热管的启动特性以及热流密度、蒸发段倾角和充液率对其传热特性的影响。
The effect on heat transfer performance caused by heat flux, gradient and liquid-filled ratio of evaporation end was deeply investigated.
用它不仅可以在线测量表面的全热流，而且还可同时测出被测表面的真实温度和发射率。
It can be used not only for the on-line measurement of total heat flow but also for the simultaneous measurements of true temperature and emissivity.
对于球锥柱模型，则着重计算头部锥体部分的热流加热率。
Regarding ball - cone-column model, then the forehead cone partial heat flux distribution is calculated emphatically.
在辐射平衡的情况下，考察了表面发射率和散射反照率对介质内辐射热流和温度场的影响。
Under the condition of radiative equilibrium, this paper examines the effects of surface emissivity and scattering albedo on radiative heat flux and temperature fields.
通过采用玻璃管和不锈钢管模拟分离式热管的蒸发段，对不同充液率和热流密度下，小螺旋管管内流体的流动与换热特性进行了实验研究。
Through the use of a glass tube and stainless steel tube a simulation was conducted of the evaporating section of the above mentioned heat pipe.
结果表明：沸腾换热系数随着热流密度和质量流率的增加而增加，随着狭缝尺寸的增加而减小。
It was shown that heat transfer coefficient increases with increasing heat flux, mass flux and decreasing gap of the annular channel.
通过垫铜皮、自制流道板紧固件并寻找热电偶测温位置，从而解决了该模具热流道漏料，产品废品率高，产品质量难以控制的难题。
Finally, we solved the problems aforesaid to caused high PPM by methods of setting copper sheets, processing fasteners and found the positions of the thermometers.
在组件封装分率较低时，热流体走管程更有利于跨膜传质。
For lower packing densities, flow of hot feed through the tube side was more beneficial to mass transfer.
在组件封装分率较低时，热流体走管程更有利于跨膜传质。
For lower packing densities, flow of hot feed through the tube side was more beneficial to mass transfer.
应用推荐