齿轮齿形采用磨齿加工,齿面采用智能控制渗碳淬火技术,齿轮的强度高、韧性和耐磨性好。
Employing abrasive machining for the form of the gear and intellective-control carburizing and quenching technology for the surface, the gear is with high intensity, strong tenacity and wearability.
结果表明,强度对淬火温度变化不敏感,而低温韧性则较敏感。
The results showed that the strength of the steel is not sensitive to the quenching temperature, but the toughness at low temperature is.
淬火时施加磁场,使合金时效后的强度和塑性有所提高。
Quenching in magnetic field can increase the strength and the elongation of the alloy after ageing.
对20钢进行不同强度交流磁场下的临界区淬火处理,观察相变后的组织。
To quench 20 steel in critical zone under different intensity alternation magnetic field and to observe the microstructure after phase transformation.
固溶、淬火等热处理手段极大地提高了其机械强度,但同时使其内部产生了较大的残余应力。
Heat treatment methods, such as solid solution and quenching, have greatly enhanced its mechanical strength, which also leave a large internal residual stress in it.
锰含量提高并选取合适的淬火温度后,残余奥氏体含量及稳定性提高,抗拉强度显著提升的同时保持了较高的伸长率。
The content and stability of retained austenite is higher after more Mn is added, and also the strength is higher with preferable elongation when the appropriate quenching temperature is chose.
阐述了超高强度的淬火回火钢(调制钢)在深海半潜式钻井平台中的应用。
This paper describes the application of high strength quenched and tempered steel in semi-submersible drilling platform.
结果表明:随着淬火温度升高,材料强度提高,韧性降低;
The results show that with the increase of quench temperature strength rise but toughness is worse;
研究了淬火、回火工艺对低碳马氏体型高强度高韧性非调质钢的组织和性能的影响。
The effect of hardening and tempering process on the organization and performance of high-strength and high-toughness non-hardened-and tempered steel of low carbon martensite is researched.
经试验分析是由于该段晶粒粗大,淬火时组织应力超过该段的材料强度所致。
Through test analysis, we found that it is caused by the large size grain in this section, as well as the structure stress in this section over the material strength.
适合加工淬火钢,合金钢,高速钢,高碳钢等硬度较硬,抗张强度较大的材料。
It can be adopted for the grinding of the hard and strong bending strength materials such as chilled steel, alloy steel, high-speed and high carbon steel.
感应淬火的目的已从仅仅提高零件的局部耐磨性扩大到提高零件的整体静强度和疲劳强度。
The aim of induction quenching has been enlarged from only improving local wear resistance to improving whole static strength and fatigue strength of parts.
结果表明,淬火温度、回火温度和运行速度对抗拉强度、屈服强度影响很大。
The results show that the quenching temperature, tempering temperature and speed have great influences on the tensile strength, yield strength.
通过淬火可以获得高强度、高韧性的铝合金,同时淬火后分布于毛坯中的残余应力幅值很大。
Although the strength and toughness of aluminum alloy 7075 can be increased greatly by quenching, this process will result in large magnitude of residual stress.
结果表明,随着淬火温度的降低,双相钢的屈服和抗拉强度下降,同时总伸长率提高;
The results showed that the tensile strength and yield strength decrease while total elongation increases with decreasing quenching temperature.
首次把感应淬火所产生的残余应力添加到了曲轴的模型里,计算了淬火前后的疲劳强度与寿命。
For the first time, the paper adds residual stress produced by hardening to the model. Then prequench crankshaft and postquench crankshaft are fatigue analyzed.
机床采用高强度铸铁,X、Y、Z向导轨淬火处理。
Equipped with high rigidity iron, x, y, Z axes are hardened.
机床采用高强度铸铁,X、Y、Z向导轨淬火处理。
Equipped with high rigidity iron, x, y, Z axes are hardened.
应用推荐