此方法可以作为重点变化单元动态分析定点测压的补充手段。
So this method may be used as a supplementary means of fixed point pressure measurements for dynamic analysis of key changeable blocks.
实例对比表明，对于没有关井测压的气井，可以用该方法反求气藏参数。
Case correlation study shows that for gas Wells without shut-in pressure survey, this method can be used to resolve the reservoir parameters.
复杂的管道可采用建立背压的方法进行清管、测径。
Complex pipe can be established by the method of back pressure pigging, caliper.
断开图3中的C、D处，利用、回油路测压法(或测泄漏量法)找到了有故障的转向缸。
Disconnect Figure 3 c, d, the use of manometry to circuit (or leakage measurement method) to find the fault has shifted the cylinder.
管线测径的目的是在试压之前确定管道存在的失圆、皱痕、凹坑或其他变形的程度和管线的通过能力。
The purpose of the pipeline caliper is determined before the pressure pipeline existing lost round, wrinkles, indentation or other and degree of deformation of the pipeline through the ability.
医用压力传感器是选用医用级聚氯乙烯、聚碳酸脂作为传感器的测压连接管和主体的材料。
Medical selection of medical grade pressure sensor is PVC, polycarbonate sensor manometry as a connecting pipe and the main material.
测压术和内窥镜可能也是必要的。
测压孔在壁上造成的间断性可以忽略不计。
The discontinuities they make in the wall are insignificant.
吃黑巧克力者每天所测收缩压(血压读取中的第一个数值)也低。
Systolic blood pressure (the first number in a blood pressure reading), measured daily, was also lower in the group eating dark chocolate.
本文首先进行了测压模型的设计，研究了测压模型尺寸的设计、材料的选取以及测点布置。
First, this paper researches the wind pressure model such as: model dimension, model material and setting survey points.
该继电器的设计思想是将过压继电器和欠压继电器集成到一起，并且实时显示所测电压值，能修改电压的上、下限。
The low-voltage relay and the excess voltage relay are integrated into one relay, which can display the real time of the voltage of the circuit and the limit of voltage can be modified.
第二是说明分压式线性传感器及其测试系统在柴油机水力测功器磅秤读数P（公斤）测量上的应用。
The second is the application of this sensor which is used for measuring the parameter P (kq) of Diesel.
结果表明：压力恢复稳态测压法求解启动压力梯度理论正确，方法简单，具有明显的优点。
The results indicate that using pressure build-up steady state pressure survey approach to calculate starting pressure gradient has obvious advantages with simple method and is theoretically correct.
阀座两边的测压点用于流量测量。
Pressure tapping points on either side of the seat provide the means for flow measurement.
本文介绍了广东液化天然气输气干线工程应用的清管测径试压技术。
This paper introduced the technology of pigging, diameter measuring & pressure testing for Guangdong LNG trunk-line.
较详细的演绎了风洞测压试验中关于风载体型系数的理论推导公式，为风洞试验数据处理提供了帮助。
The paper deduces the theoretical derivation of figure coefficient of wind load in wing tunnel test, which can do help data processing of wing tunnel test.
目的研究人工测血压的最佳时间和测压次数。
Objective To study the best time and times of artificial taking blood pressure.
本文总结了中原石油勘探局勘探公司使用深井压塞液的经验教训，对测声波仪器遇阻问题进行了分析。
In this paper the experience of Exploration Company, Zhongyan Petroleum Exploration Bureau, in using displacement fluids in cementing deep wells is summarised.
介绍了光学压敏涂料测压技术原理，光学压敏涂料的研制和其在风洞试验中的应用。
The principle and preparation of optical pressure sensitive paint and its application in wind tunnel test are introduced.
介绍了液压型光电式测压计的设计原则、结构特征、测试原理、试验方法及其技术性能。
The design principle, structure characters, testing principle and method, and technique capability of hydraulic photoelectrical pressure gauge are presented.
针对不同的发动机点火状态，在射流轴线的不同距离上对一系列测点位置的总压参数进行了测量。
According to the different motor ignition states, a series of total pressure values of observed points on the respective jet axis distances was measured.
本文为NACA0012翼型在NH - 1风洞进行跨音速二维测压实验的研究报告。
This paper is a report of experimental pressure. Measurement research for NACA0012 airfoil in NH-1 transonic wind tunnel.
将测压原理拓展应用到均匀送、排风管路的设计中，并探析了这种管路的作用机理及计算方法。
Applies the pressure measuring principle to the ducts for even air supply and exhaust, and analyses the function mechanism of such ducts and their application calculation.
目的探讨肛管直肠测压技术的临床应用和意义。
Objective To evaluate the clinical appliance and significance of the technique of anorectal manometry.
透气性测定通过恒压气源吹气测压法实现，透气性探头的核心部件是微压差传感器。
Permeability is measured by constant pressure air source blowing, core of the detector is micro differential pressure sensor.
位移测试装置利用高精度差动变压器位移传感器完成塑性测压器件的变形量（或压后高）的测量；
The deformation or the highness after shooting of the plastic pressure-measuring elements is measured by the high precision LVDT displacement sensors in length testing device.
介绍了用于水下发射膛压测量的压力传感器，针对水下测压时有无充脂所出现的不同现象，以理论推导分析了产生此现象的原因。
The pressure sensor used in under water gun, and the abnormal phenomenon in pressure measurement are introduced, the cause of abnormal phenomenon is analyzed in theory.
介绍了用于水下发射膛压测量的压力传感器，针对水下测压时有无充脂所出现的不同现象，以理论推导分析了产生此现象的原因。
The pressure sensor used in under water gun, and the abnormal phenomenon in pressure measurement are introduced, the cause of abnormal phenomenon is analyzed in theory.
应用推荐