连杆与活塞的连接是采用活塞销。
The connecting rod is attached to the piston by the piston pin.
活塞销产品实行“三包”服务；
异型活塞销孔闭环加工系统研究；
Research of Heterogeneous Type Piston Pin Boss Hole Closed Loop Processing System.
本文建立了浮动式活塞销的运动方程。
The equation describing the motion of the floating piston pin is deduced in this paper.
还包括一种形成活塞销(10)的方法。
连杆小头连接着活塞销。
The connecting rod little end is connected to the piston pin.
简要分析了活塞销冷、温挤压工艺的特点。
The process features of the cold and warm extrusion for the piston pin have been simply compared.
新涂层工艺适用于汽缸套，凸轮轴和活塞销。
Cylinder sleeves, camshafts and piston pins can be coated with the new method.
运用该方法可以对浮动式活塞销轴承故障进行分析。
This method can be used to analyse the causes of failure of floating piston pin bearings.
运用该方法可以对浮动式活塞销轴承故障进行分析。
This method can be used to analyse the causes of failure of floating piston pin …
运用该方法可以对浮动式活塞销轴承故障进行分析。
This method can be used to analyse the causes of failure of floating…
运用该方法可以对浮动式活塞销轴承故障进行分析。
This method can be used to analyse the causes of failure of floating PI...
分析了冷挤压活塞销凸模的受力情况和主要失效形式。
The stress and the main failure form of the cold extruding die for the piston pins were analyzed.
阀杆断裂了把液压马达吊上岸去修理制作十个活塞销。
Crane the hydraulic motor ashore for Fabricate ten gudgeon pins.
本厂是汽车发动机液压挺杆和活塞销的专业化生产企业。
The factory is Tappet car engine and hydraulic piston pin the specialized production enterprises.
介绍了活塞销冷挤压的生产工艺、模具设计及制造特点。
The forming process, die design and some manufacturing main points in cold extrusion of piston pins are presented in this paper.
在活塞中活塞销孔也同样为活塞销形支承面，其作用为连接连杆。
The piston pinhole in the piston also serves as a bearing for the piston pin, which is used to connect the connecting rod.
本文介绍红外线监测电路的原理以及在活塞销电涡探伤仪中的应用。
The principle of infrared observation circuit and its application in piston pin electric eddy-current defectoscope is introduced in this paper.
引入滚滑状况下的摩擦力系数，从而求得活塞销运动方程的数值解。
The numerical solution of the equation describing the motion of the floating piston pin is obtained by bringing in the conception of friction force coefficient under slide-roll condition.
连杆的一端与曲轴的连杆轴颈相连，另一端通过活塞销与活塞相连。
The connecting rod is attached at one end to a crankpin on the crankshaft and at the other end to a piston, through a piston pin or wrist pin.
随着柴油机强化度的提高，浮动式活塞销轴承因过热而产生的故障屡有所见。
As the output of diesel engines is increased, failures of floating piston pin bearings caused by overheating have often been reported.
分会专业生产各种类型的摩托车、汽车、柴油机、空压机等活塞、活塞销产品。
We specialize in piston and piston pins for various motorcycles, autos, diesel engines, air compressors and so on.
据此提出了活塞结构改进设计措施，采用了在活塞销孔内嵌入铸铝青铜衬套结构。
It proposes measures of improving piston structure design and adopts the structure of cast aluminum bronze embedded in the hole in the piston pin bushing.
通过冲连皮工艺试验及批量生产，证明采用冲连皮工艺能够应用于活塞销加工过程；
The effective adopting stamping process on piston pin product quality and belemnoid demension is explained;
通过冲连皮工艺试验及批量生产，证明采用冲连皮工艺能够应用于活塞销加工过程；
Through stamping technology test and batch yield, it is proved that the process can be applicable to piston pin manufacture;
明确指出妨碍活塞销冷挤压技术在国内推广应用的关键因素是其冷挤压凸模的寿命太短。
It is pointed that application and dissemination's key factor of piston pin's cold extruding technique in China is that working life of piston pin's cold extruding punch is too low.
活塞销贯穿活塞，把连杆小头与活塞连在一起，并将连杆保持在活塞中心的适当位置处。
The piston pin fits through one side of the piston, through the small end of the rod, and then through the other side of the piston. It holds the rod firmly in place in the center of the piston.
活塞销贯穿活塞，把连杆小头与活塞连在一起，并将连杆保持在活塞中心的适当位置处。
The piston pin fits through one side of the piston, through the small end of the rod, and then through the other side of the piston. It holds the rod firmly in place in the center of the piston.
应用推荐