清洁泵体，检查阀门是否附着有泥沙。
如果泵不起诉，建议您以填补泵体的手。
If the pump is not charged, you are advised to fill the pump body by hand.
螺杆与泵体紧密贴合。
设有泵体密封环，而叶轮密封环为可选用件。
Sealing ring is fitted on pump body, while impeller sealing ring is an optional part.
本文介绍了某种射流泵泵体加工的系列专用夹具。
This article introduces a series of special clamps for machining pump body of a Shoot Liquid pump.
该泵为离心设计，叶轮与泵体的轴向间隙均相同。
The concentric design allows the distance between the impeller and the housing to be the same at all points.
安全阀可以与泵体或泵盖铸成一体，也可以单独装配。
The relief valve can be cast and pump body and pump cover, also can separate assembly.
安全阀可以与泵体或泵盖铸成一体，也可以单独装配。
Safety valve can be covered with the body or pump Zhucheng one, can also be a separate assembly.
透明管和泵体的材料一致，硬度相当，具有同样的寿命。
Transparent tube and pump body of material consistent, hardness, have the same life.
结果表明，两种改进方案泵体的受力和变形均有所改善。
The results for tha the stress and the deformation in two new bodies are improved .
因此，泵体与螺杆外圆表面及螺杆与螺杆间隙应尽可能小些。
Therefore, the pump body and screw cylindrical surface and screw and screw clearance should be as small as possible.
泵体是由铸铁铸造毛坯成型，出现严重磨损时应更换新件。
Pump body is by cast iron casting blank forming, severe wear new thing should be changed.
因此，泵体与螺杆外圆表面及螺杆与螺杆间隙应尽可能小些。
Therefore, the pump with the screw and screw and screw cylindrical surface gap should be as small as possible more.
论述了泵体零件的三维设计和数控加工以及NC代码的生成。
This article introduces three-dimension design and NC machine and simulation of pump, the NC machine and simulation of the part is in the MasterCAM.
所述喷嘴体朝泵体的外部延伸，以便将增压油供至一个燃烧器。
The nozzle body extends towards the outside of the pump body to provide a burner with supercharging oil.
kcb齿轮泵主要有齿轮、轴、泵体、安全阀、轴端密封所组成。
KCB gear pump are mainly gear, shaft, pump body, valve, shaft end seal.
海洋级铝泵体与丽绚衬砌是一个强有力的证明，泵的设计寿命长。
Marine grade aluminium pump body with Rilsan lining is a proven robust pump design for long life.
试验证明，采用挤压铸造新工艺可以获得优质的铝合金泵体铸件。
It has been proved that to make use of squeeze casting to produce the body of gear pump can get good quality casting of aluminum alloy.
泵体和叶轮间形成环形流道，吸入口和排出口均在叶轮的外圆周处。
Impeller and the body formed between circular flow, I inhaled and exports in the row outside the circumference of the impeller.
泵的轴封采用机械密封，泵体顶部和底部分别装有注水、放泄的螺塞。
Pump shaft seals use mechanical seal, pump top and bottom, respectively, equipped with water injection plug and the drain plug.
泵体和泵盖构成泵的工作室，泵体的入口为水平方向，出口垂直向上。
The pump body and pump cover composes the pump studio. The inlet of the pump body is horizontally while the outlet is straight-up.
需要特别指出的是，液体质点在泵体流道内的圆周速度小于叶轮的圆周速度。
Particularly necessary to point out that the liquid in the pump body mass flow rate of less than the circumference of the circumferential speed of the impeller.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
The pump comprises mainly of pump body, cover, impeller, shaft, seal ring, intermediate support, sealing and suspension assembly, etc.
泵主要由泵体、泵盖、叶轮、轴、密封环、中间支架、密封和悬架部件等组成。
The main parts include pump body, pump cover, impeller, axis, sealing rings, intermediate support, sealing and suspension parts and other components.
结果表明：泵体裂纹为相变应力和热应力以及材质冶金质量不高共同作用而产生。
The results show that the cracking of the pump body resulted from the interaction of phase transformation and heat stress, as well as the poor quality of metallurgy.
泵体与方向控制阀组合，并内置可调溢流阀，单向阀，可大大简化系统的设计与安装。
The pump body combination with control valve, and with built-in adjustable relief valve, one-way valve, it could greatly simplify the system design and installation.
TY B系列调压注水装置由双缸四腔泵体、电液换向阀、控制液路及控制电路组成。
TYB series waterflood pressure regulating systems consist of two cylinder four chamber pump body, electro hydraulic reversing valve, control fluid circuit and control current circuit.
根据石油油库自吸离心泵泵体破裂的状况，对其破裂原因进行了分析，提出了防止措施。
Based on the status of the cracking of self-suction centrifugal pump in oil farm, the paper makes an analysis on the reasons of cracking and puts forward the measure of prevention.
排除：放松填料，疏通引水槽；拆开泵体清除杂物、除锈；拆下泵轴校正或更换新的泵轴。
Ruled out: relax fill, dredge flume; disassemble pump body to remove debris, rust; Calibration shaft removed or replaced a new shaft.
精密加工的泵体可使“D”型轴承与齿轮轴精确配合，确保齿轮轴不偏心，以防齿轮磨损。
Precision machining pump body can make "d" type bearings and gear axle, ensure accurate gear axis gear eccentric wear, not to.
应用推荐