油盘通常用的薄钢板冲压制成。
接油盘：用于盛接烤肉时的油滴的盘。
Drip pan:a pan for catching the drippings from roasting meat.
选取了几组缸体与配油盘进行对比实验。
Choose several group cylinder block with mix oil record go on experiment of comparing with.
使用滴油盘和防护装置。
机油再流下来回到油盘。
卷放在金属箔上，放在滴油盘上置于烤架上。
Place meat loaf on foil; place on the grill rack over drip pan.
依其设计不同，油盘的容量通常由5到10升不等。
It usually holds 5 to10 litres of oil, depending on the engine design.
依其不同的发动机，油盘的容量通常从5到10升不等。
It usually holds 5 to 10 liters of oil, depending on the engine design.
对CA151型汽车制动鼓挡油盘拉延成型工艺进行了探讨。
Drawing process for shaping the brake drum oil shield of truck CA151 has been deliberated.
油盘和气缸体的下部一起被称为曲轴箱，用来封闭或罩住曲轴。
The oil pan and the lower part of the cylinder block together are called the crankcase; they enclose, or encase, the crankshaft.
本文介绍了对轴向柱塞泵配油盘进行有限元分析的方法和结果。
The procedure and results of a finite element analysis on the oil distributing plate of an axial piston pump are introduced.
不要直接把面包放在黄油盘里，而是取些黄油放在你的面包碟里。
And never butter your bread directly from the butter dish. Instead, transfer some butter from the butter dish to your bread plate.
然后，我将一汤匙的油盘和加热的油，直到它开始微光-约1分钟。
Then, I added 1 Tablespoon of oil to the pan and heated the oil until it started to shimmer - about 1 minute.
文中还根据配油盘表面的磨损形貌，找出了合理选择配油副材料的依据。
In the light of surface morphology of oil-distributing pair a criterion for selection of optimum material of oil-distributing pair is found.
通过对发动机机油盘拉伸工艺的分析，确定了此复杂阶梯盒形件的拉伸工艺。
Through the analysis of the drawing technology for the engine oil disc, the process for drawing this complex stepped boxed-shaped part was determined.
轴承内侧装设的甩油盘就是借离心作用将可能进入轴承内部的油甩掉，起到密封的作用。
Bearing off the inside of oil pan installed by the centrifugal effect is likely to enter the oil off the internal bearings, seals play a role.
比如，可以向被服务方说明设置接油盘、灭火器、操作现场配合等的必要性及有关要求。
For example, to be able to service side note set drip pan, fire extinguishers, operating the site with the necessity and the relevant requirements.
分析结果表明，配油盘的强度满足设计要求，但配油盘表面变形较大，远远超过配油盘的平面度要求。
The results show that the plate strength meets design requirement. The plate surface distortion however, exceeds flatness specification.
第三章对现有的灭火实验室2B油盘火从点燃到稳态燃烧进行了数值模拟，确定FDS软件使用中的最优参数设置。
In chapter 3, numerical simulation of 2b pool fire from ignition to steady combustion, fix on the best parameter in FDS.
本发明公开了一种液面传感器，其包括与位于需要检测液面的油盘或其它容器的底部中的集成电路耦连的平行板电容器。
A fluid level sensor comprises a parallel plate capacitor coupled to an integrated circuit located in the bottom of an oil pan or other receptacle in which fluid level is being sensed.
斜盘中心线和缸体中心线相交一个倾角δ。高压油经配油盘的窗口进入缸体的柱塞孔时，高压腔的柱塞被顶出，压在斜盘上。
High-pressure oil pan with oil as a window into the cylinder hole of the plunger, the high-pressure chamber was the top of the plunger, the pressure in the oblique plate.
本文介绍油隔离泵阀箱渗漏的原因，能过对阀盖O型圈沟槽的改进及采取乐泰密封胶替代牛油盘根进行密封，解决了阀箱渗漏的问题。
This paper introduces the cause of the seepage in valve box of oil isolation pump, and solves the problem of the valve box seepage by way of the improvement of die slot in O - ring and seal material.
结果表明：由于焊接电流过大，使焊缝产生淬火马氏体组织及较大的焊接残余应力，导致镀锌氢脆敏感性增加，造成吸油盘发生氢脆开裂。
The large welding current caused the formation of quenched martensite and the high residual stresses in the welding zone, resulting in the increase of zinc sensitivity of hydrogen attack.
结果表明：由于焊接电流过大，使焊缝产生淬火马氏体组织及较大的焊接残余应力，导致镀锌氢脆敏感性增加，造成吸油盘发生氢脆开裂。
The large welding current caused the formation of quenched martensite and the high residual stresses in the welding zone, resulting in the increase of zinc sensitivity of hydrogen attack.
应用推荐