• 如果发动机回火,进气歧管骤增的压力就迫使阀门向后移动。

    If the engine backfires, the sudden pressure in the intake manifold forces the valve back.

    youdao

  • 燃料系只有这样几个主要部件,如燃油箱、输油泵、燃油滤清器、化油器、进气歧管等。

    The fuel system only has several major parts such as fuel tank, fuel pump, fuel filter, carburetor, intake manifold, etc.

    youdao

  • 废气经另外一个排气歧管排出。

    The exhaust gas exits through the other exhaust manifold .

    youdao

  • 清洁排气歧管和汽缸头配合面。

    Clean the exhaust manifold and cylinder head mating surfaces.

    youdao

  • 废气经另外一个排气歧管排出。

    The exhaust gas exits through the other exhaust manifold.

    youdao

  • 废气经另外一个排气歧管排出。

    Thee exhaust gas exits through the other exhaust manifold.

    youdao

  • 歧管必须无酒精才能正常工作。

    The manifold must be alcohol free to function properly.

    youdao

  • 在压缩机歧管配件里安装高压释放阀。

    Install the high pressure relief valve in the compressor manifold fitting.

    youdao

  • 排气歧管采用螺栓联接固定在气缸盖上。

    The exhaust manifold is bolted to the cylinder head.

    youdao

  • 注塑成型工艺是开发塑料进气歧管的重要环节。

    The injection molding is an important tache to exploit plastic air intake manifold.

    youdao

  • 废气从排气歧管流入排气管,进入催化转换器。

    The exhaust gas flows from the exhaust manifold into an exhaust pipe and from there into the catalytic converter.

    youdao

  • 一种喷杆包括在喷杆上的一个歧管或多个歧管。

    A spray bar includes a manifold or multiple manifolds located on the spray bar.

    youdao

  • 采用流固耦合方法计算了内燃机排气歧管的热应力。

    The thermal stress of internal combustion engine exhaust manifold was calculated with the fluid-structure coupled simulation.

    youdao

  • 首先对发动机及其进气歧管的结构功能进行了分析。

    First, the structure and function of the engine air intake manifold are analyzed.

    youdao

  • 一种部件,例如进气歧管或节气门本体,具有空气通道。

    A component, such as an intake manifold or a throttle body, has an air passage.

    youdao

  • 活塞主要因进气歧管真空度的变化而在活塞腔内上下移动。

    The piston moves up and down in the piston chamber primarily in response to changes in intake manifold vacuum.

    youdao

  • 总结出了在设计塑料进气歧管注塑模具时要注意的几个问题。

    Summarized some important experience on designing injection mould of plastic air intake manifold.

    youdao

  • 这是因为当发动机熄火时,进气歧管冷却而产生轻微的真空。

    When the engine is shut off, the intake manifold cools and a slight vacuum forms as a result .

    youdao

  • 安装汽缸盖,进气歧管和排气管,请参阅本部分的汽缸盖安装。

    Install cylinder head, intake manifold, and exhaust manifold, refer to cylinder head installation in this section.

    youdao

  • 由于排气歧管的法兰与排气口未呈现相应的匹配,气流受到限制。

    Because the stock manifold's flange does not align squarely with the ports, flow is restricted.

    youdao

  • 材料通常为铸铁的排气歧管是将废气从燃烧室引入排气管的管道。

    The exhaust manifold, usually constructed of cast iron, is a pipe that conducts the exhaust gases from the combustion Chambers to the exhaust pipe.

    youdao

  • 排放通道连接到排放歧管,并且柴油颗粒过滤器布置在排放通道中。

    An exhaust passage is connected to the exhaust manifold and a diesel particulate filter is disposed in the exhaust passage.

    youdao

  • 其分析结果表明改进效果良好,排气歧管罩的辐射噪声得到明显降低。

    The analysis of the improved structure shows that the measures are effective, the radiate noise of the cover is decreased distinctly.

    youdao

  • 介绍了发动机进气歧管压力传感器的标定系统和传感器静、动态标定方法。

    This paper introduces the calibration system and static and dynamic calibration method of an engine intake manifold pressure sensor.

    youdao

  • 随着拖动转速升高,进气歧管压力降低,对应的喷油策略也应随之调整;

    The intake manifold pressure is lower when the cranking speed increases, thus the fuel metering strategy should be modified.

    youdao

  • 本文主要进行可变式进气歧管的三维曲面重建和空气流动模拟分析的研究。

    This thesis mainly carries on research of three dimensional surface reconstruction of variable intake manifold and air fluid simulation analysis.

    youdao

  • 介绍了以快速原型技术和精密铸造技术进行进气歧管铸造模具制造的情况。

    The situation of mould manufacturing for inlet manifold in rapid prototyping and investment casting was introduced.

    youdao

  • 节气门体总成安装在歧管口,进气歧管接口尺寸如节气门体总成轮廓图所示。

    The Throttle body assembly will mount to the manifold snout and intake manifold interface dimensions are defined on the Throttle body assembly outline drawing.

    youdao

  • 中硅钼蠕铁的抗热疲劳性能为普通蠕铁的3倍,因而是制造排气 歧管的理想材料。

    The thermal properties of medium silicon-molybdenum vermicular iron are about three times of that of normal vermicular iron, so it is an ideal material for producing manifold.

    youdao

  • 中硅钼蠕铁的抗热疲劳性能为普通蠕铁的3倍,因而是制造排气 歧管的理想材料。

    The thermal properties of medium silicon-molybdenum vermicular iron are about three times of that of normal vermicular iron, so it is an ideal material for producing manifold.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定