尺蠖驱动器按锁模机构分类。
Inchworm actuators are classified by the clamping mechanism.
介绍了2005年诺贝尔物理学奖的获奖工作-用锁模飞秒激光光梳去测量光的频率。
The work of the winners of the 2005 Nobel prize in physics is briefly reviewed. They measured the frequency of light with mode-locked laser comb.
锁模力是注塑机一个非常重要的参数,它是注塑机在注射过程中保持模具闭合状态以抵御型腔压力所提供的最大压力。
Clamping force is an important attribute of the clamping unit of a PIMM. It is the maximum force the machine is capable of to keep the mould closed against the cavity pressure during injection.
锁模不仅可用损耗调制取得,也可用位相调制来得到。
Mode locking can be induced not only by loss modulation, but also by phase modulation.
用傅里叶变换的方法分析了锁模激光器中模式间的相位和振幅涨落对锁模脉冲列特性的影响。
The Fourier transform method has been used to analyze the influence of modal amplitude and phase fluctuations in a mode-locked laser on performance of its output pulse.
球墨铸铁模板及机铰经电脑机床加工,组成精密锁模系统;
S. G. iron mould platens and toggles after cutting by computer controlled machine, form precious clamping unit.
如果排气口的确存在,尺寸合适并且干净,那么减少锁模力会有助于排气,并使注塑更快。
If vents do exist, and they are properly sized and clean, then reducing the locking force can help with venting and enable faster injection time.
本文分析了SESAM锁模与染料可饱和吸收体锁模的区别,提出了SESAM锁模机理的初步模型。
In this paper, we analyse the difference between SESAM and dye, and present the initial model of the mechanism of SESAM mode-locking.
本文对被动锁模激光器的涨落模型作了改进。
The fluctuation model of passively mode-locked lasers has been improved.
为了获得稳定的谐波锁模脉冲,分析了有理数谐波锁模的理论和非线性放大环镜的传输特性。
To achieve a steady harmonic mode-locked pulse (HMLP), the theory of rational harmonic mode-locking and the transmission characteristics of a nonlinear amplifying loop mirror were analyzed.
因此,SESAM除了其量子阱材料的可饱和吸收效应能启动锁模外,本身的负克尔效应也有助于锁模的自启动。
These reveal that the negative Kerr effect of the SESAM can contribute to the self-starting of mode-locked lasers besides the saturable absorption mechanism.
理论分析了利用非线性偏振旋转效应锁模激光器的机理。
The physical mechanism of nonlinear polarization rotation mode-locking was analyzed in theory.
输出锁模脉冲的基频为几兆赫兹。
我们都知道对于相应的产品投影面,如果没有足够的锁模力的话,可能会有飞边产生。
We all know that if you don't have enough clamp force for the projected area of the parts, flash will result.
并利用类可饱和吸收体实现被动锁模的自启动条件,给出了用小信号光斑变化量表示的克尔透镜锁模启动条件。
The self-starting condition expressed by the small signal spot size variation is demonstrated, according to the passive absorber-like self-starting condition.
边缘温度的突然下降是产生锁模不稳定性的重要标志。
The drop of edge temperature is an important feature of appearance of the locked mode instability.
鉴于锁模力的理论计算较为复杂,本文提出了一种简化的计算方法。
Because the theoretical calculating method of clamp force is very complex, a simplified experiential calculating method is provided.
本机合模装置属液压式结构,主要由导柱、动模板、支承板、锁模油缸等组成。
This device adopts hydraulic structure and is mainly made up of guide pole movable platen support plate and clamping cylinder etc.
预测可能存在的熔接痕位置及锁模力的大小,确定最佳浇口位置。
In order to obtain the best gate location addition, the position of weld lines and the clamp force were forecasted.
它采用主-被动锁模相结合的染料激光脉冲与碘激光脉冲同步工作。
The dye laser pulse has been synchronized with the iodine laser pulse by a combination of active-passive mode-locking.
在相应于谐波锁模、有理数谐波锁模条件下得到了稳定的脉冲输出。
Steady pulses were obtained on harmonic and rational harmonic mode-locked status.
注塑生产中,锁模力参数设计十分重要。
Clamp force parameter setting is very important in plastic injection molding.
介绍了一种塑料中空成型设备的锁模机构的新设计,并对其结构、工作原理和性能进行了分析。
This paper introduces a new design of clamping unit used in blow molding machine, and analyses the structure, the working principle and the performance.
分析了相位偏置和光纤的色散对锁模机制的影响,获得了产生稳定超短光脉冲的条件。
The effects of phase bias and group velocity dispersion on mode locking mechanism are analyzed. The operating conditions for stable short pulse generation are obtained.
介绍了半导体可饱和吸收镜(SESAM)的基本结构及使用半导体可饱和吸收镜被动锁模固态激光器的基本原理。
The basic structure and the fundamental principle of semiconductor saturable absorption mirrors (SESAM) that are used for passive mode-locking solid-state lasers are introduced.
对于均匀展宽激光器的非线性镜锁模,提出了一种解析分析方法。
This paper presents a closed form analysis method of nonlinear mirror mode lo-cking of a homogeneously broadened Laser.
为了获得振幅均衡的有理数谐波锁模脉冲,必须在原有的实验装置中添加一个掺铒光纤放大器(EDFA)以提高注入调制光信号功率。
For obtaining a pulse series with a small amplitude ripple, an Erbium-doped Fiber Amplifier (EDFA) must be added into the primary experiment setup to enhance injection-modulation signal power.
由此,对这类混合锁模激光器系统的特性作了理论解析。
Based on these results, some characteristics of such a hybrid mode-locked lasers system are interpreted theoretically.
对主动锁模光纤激光器的锁相环进行改进,提出一种新型的“变带宽锁相环”的设计结构。
This article presents a new design structure of variable bandwidth phase-locked loop based on improving phase-locked loop of actively mode-locked fiber laser.
对主动锁模光纤激光器的锁相环进行改进,提出一种新型的“变带宽锁相环”的设计结构。
This article presents a new design structure of variable bandwidth phase-locked loop based on improving phase-locked loop of actively mode-locked fiber laser.
应用推荐