• 上模芯和下模芯采用硬质合金材料。

    The upper and the lower mould cores are made of hard alloy materials.

    youdao

  • 散热器进出水管剖切模采用浮动凹模芯轴结构形式。

    A structure form of floating matrix core shaft has been adopted in the die for slitting the water pipe of the radiator.

    youdao

  • 得到模芯的长度后,根据模芯座的结构尺寸确定模芯装配尺寸;

    3 get the core length, core assembly size is determined according to the structure size of the mold core seat;

    youdao

  • 通过实例介绍了具有小模芯的铝型材挤压模的设计和制造方法。

    The technology of designing and making for extrusion die with small die-mandrel by several examples is introduced.

    youdao

  • 介绍拉丝模模坯、模套的加工及模芯装镶过程中应注意的要点;

    To introduce the points needed to be attended during machining the die blank and die sleeve and inserting die core.

    youdao

  • 详细阐述了硬质合金模芯镶块剖分式组合凹模的结构和制造工艺。

    The structure and manufacturing engineering of combination die which was made up of steel-bonded carbide core and insert block were expatiated.

    youdao

  • 介绍了等静压瓷砖模具的工作原理、上模芯的结构形式和优化设计的方法。

    This paper introduced the working principles of ceramic tile die with static-pressure, structure type of upper punch and method of optimal design.

    youdao

  • 介绍采用热化学共渗法对硬质合金拉丝模芯进行超硬化处理,以提高其表面硬度的方法。

    The article introduces the method of superhardening treating hard alloy drawing die core with thermochemistry copermeation method so as to improve its surface hardness.

    youdao

  • 采用LD钢制造大型滚子冷镦模具的模芯,具有较理想的硬度、强度、耐磨性和冲击韧性。

    Core of large roller cold upsetting die made of ld steel has more ideal hardness, strength, anti wear capacity and impact toughness.

    youdao

  • 本实用新型的目的在于提供一种合金大锭模芯,以克服合金大锭不便于桥式吊车机械手抓吊的弊端。

    Objective of the utility model is to provide an alloy big ingot mould core to overcome the problem that alloy big ingot is not suitable for gantry crane manipulator grasping.

    youdao

  • 提出了一种浮动凹模芯模闭式镦粗法,以解决厚壁管在单向加压的普通液压机上进行闭式镦粗后壁厚不均的问题。

    Using closed die upsetting process to manufacture thick wall tubes on normal hydraulic press may cause the dis uniformity of the thickness along the length of the tube.

    youdao

  • 模具变形分析结果表明,随着焊合室深度增加,模芯变形程度增大,对应力分布来说,存在一个最佳的焊合室深度。

    Die stress analysis results show that the deformation of the die core increases with welding chamber height. For the stress distribution, there exists a best welding chamber height.

    youdao

  • 针对电刷端盖压铸件结构及工艺要求,选择端盖口部大端面为动静模分型面,铸件上各成形小孔由动静模型芯对接组成,浇注系统采用中心浇道。

    The small formation holes in the brush cover was constructed with the mold core in moving and static container, and center ingate was employed to the gating system.

    youdao

  • 该改进设计主要是在定模部分增加型芯,并将一次分型改成二次分型,再使倒锥部分实现强制脱模。

    The improved design is increased in the fixed mold core, which change first parting into second parting and demould the inverted cone mandatorily.

    youdao

  • 空心型芯与固定在动模上的液压抽芯器相连。

    Hollow core was linked with hydraulic loose-core implement fixed on the moving die.

    youdao

  • 最后,本文又对一种低折射率芯光子晶体光纤基模束缚损耗特性进行了分析。

    Lastly, the fundamental mode loss of a special kind of depressed-index core PCF is analyzed.

    youdao

  • 介绍了共挤出的PVC芯层发泡管的工艺流程和模头装置,并讨论了共挤管材的原材料选择及配方构成。

    The processing technology and coextrusion die design of PVC foam core pipes are introduced. Also the selection of raw materials and design of formulation are discussed.

    youdao

  • 首先,在芯模外侧创建与铺丝路径相对应的特定曲线,然后将曲线按特定方向投影在指定的偏置曲面上,形成初始路径。

    First, a specific curve is created around the core module, and then it is projected on to specified surfaces in a particular direction and the projections are taken as initial paths.

    youdao

  • 热膨胀硅橡胶适于制造热膨胀芯模。

    The latter is suitable to make thermal expansion core mould.

    youdao

  • 基于自主研制的七自由度铺丝机,研究具有芯模的封闭构件自动铺丝路径规划技术,设计了通用的铺丝路径生成算法,可生成任意角度的铺丝路径。

    Based on the seven-degree-of-freedom fiber placement equipment independently developed, the fiber placement path planning for closed composite parts with core models is researched.

    youdao

  • 从而得出了丝嘴运动轨迹坐标和芯模转角的计算公式。

    And therefrom three formulas for calculating the coordinates of the eye movement track and the rotating angle of mandrel are given.

    youdao

  • 这种光纤的纤芯折射率比包层基质折射率小,所以短波长时基模损耗迅速增大,使得光传输截止。

    The index of the core is a little smaller than that of the cladding base material, so the fundamental mode loss of short wavelength increases rapidly and leads to the mode cutoff.

    youdao

  • 开模时,压铸机开模力驱动交叉复合弯销机构进行铸件内侧凹抽芯,然后液压抽芯器抽拔杯形型芯。

    The opening force of die casting machine drives the crossed compound dog-led CAM mechanism draw core in inboard concave, and then make the hydraulic loose-core implement to draw the hollow core.

    youdao

  • 针对把手注射模的新设计,阐述了把手注射模的结构形式,并重点分析了模具斜顶抽芯机构的设计。

    Aiming at the new design of handle injection mould, the author expatiated the structural form of handle injection mould and analyzed the design of mould slanting tip core machine.

    youdao

  • 介绍大屏幕彩色电视机前壳注射模结构,重点介绍侧抽芯大滑块的设计, 顶出机构和进浇方法的改进。

    The injection mold structure of the front shell of large screen color TV is introduced, and design of side core-pulling large slide, improvement of ejector mechanism and gating method are introduced.

    youdao

  • 以硅橡胶材料制作的芯模与钢模组合使用制备碳纤维复合材料制件,应用效果较好。

    The core mold made of thermal expansion silicon rubber is used with steel mold to mold CF composite products with good result.

    youdao

  • 介绍了塑料管套注射模的环形型芯抽芯机构。

    A kind of ringed core pulling mechanism of injection die of plastic casing coupling is introduced.

    youdao

  • 我们前面已经叙述了我们需要从型芯上卸下塑件,而且塑件是跟随型芯的,因此型芯也最好设置在动半模。

    We have stated previously that we need to eject the molding from the core and it therefore follows that the core, too, will most satisfactorily be located in the moving half.

    youdao

  • 玻璃纤维芯有两种基本的类型:多模光纤,用于10km以下的距离;单模光纤,用于更长的距离。

    The glass fiber core comes in one of two basic types: multimode fiber for distances up to 10km and single-mode fiber for longer distances.

    youdao

  • 本课题主要研究椭圆芯光纤的传播特性,为研究基于模间干涉的光纤电压互感器奠定理论基础。

    The research on the propagation characteristics of elliptical-core fiber in this paper is a basic theoretical research work for the study of the voltage sensor based on modular interference.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定