通过对斜顶杆工作过程的逆向思考,采用拔杆为后模滑块提供动力。
Through reverse thinking of working principle of inclined push rod, this mold adopts button pole to offer power to rear mold slide block.
于上架梁的下方固定有顶杆和凹模,于下架梁上安装有其一端部至少有一个肩凸的型芯。
An ejector rod and a female die are fixed at the lower part of the upper beam, and a mold core is mounted on the lower beam. The end of the mold core has at least one shoulder.
采用四导杆导向,刚性好,导向精度高。节省操作时间,合模平稳。
It adopts four guide rods with a high accuracy in guiding, which saves working time and helps the upper and lower moulds matched steadily.
人们提出采用二极模稳定杆使二极模频率远离四极工作模。
Dipole stabilizer rod was proposed to shift the dipole modes far from the working quadrupole mode.
本文针对由二轮驱动的移动平台和二连杆机械臂组成的移动机械臂的输出跟踪问题,利用滑模控制原理为其设计了动态滑模控制器。
A dynamic sliding mode controller is devised to achieve output tracking of the mobile manipulator that consists of a mobile platform which has two driving wheels and a two-link manipulator arm.
当使用任何闭合式挤压模时,选择线径稍大于成品柄杆的金属丝成型效果最佳。
With any contained extrusion die, best results are often obtained by forming wire that is somewhat larger in diameter than the finished shank.
这样,开槽的锚杆就可以在成锥模内成锥。
In this way, the grooving anchor rods can taper in the tapering die set.
规格:平头冷墩模、沉头冷墩模、一序冲顶模、缩杆模等。
Specification: flat head cold-flow model, countersunk head cold-flow model, primary drawing mould, pole-shorten model, etc.
本文针对由二轮驱动的移动平台和二连杆机械臂组成的移动机械臂的输出跟踪问题,利用滑模控制原理为其设计了动态滑模控制器。
The variable structure model was based on the sliding mode control theory to switch the different control strategies of acquisition and pursuit tracking.
定期清洁机台表面、底板及下模滑板、沟槽、上模内压板及保险杆(注:必须关闭电源并恢复常温)。
Clean the machine including the surface, base, slip board, groove, pressed board and oriented pole in the fixed time. (turn off the power until the machine to normal temperature).
本文主要介绍根据CAD造型数据计算上下模冲压顶杆的高度,并开发一台顶杆高度自动调节机械手调节离散型面模具顶杆高度。
The object of this dissertation is to calculate the height of screw mandrils from CAD data and develop a mechanical hand to adjust screw mandrils' height automatically.
提出了利用二次模变换计算同杆双回输电线路潜供电流与恢复电压稳态值的方法。
A new method for calculating secondary arc current and recovery voltage on double-circuit transmission lines by twice-model transformation was proposed.
系统由超声波驱动器、换能器、变幅杆、拉丝模、拉伸机等组成,通过对黄铜丝的拉拔实验,考察了超声振动对拉拔力和丝的表面质量的影响。
Through a series of drawing experiments of brass wires, the effects of ultrasonic vibration on drawing force and surface quality of the wires were discussed.
对模切机模切加载过程进行分析,采用数学方法拟合了一条加载过程曲线,确定了肘杆机构可承受的最大模切压力值。
After the analysis of loading process, a loading curve is simulated by math method, which fixes on the most press value that can be endured by elbow-bar framework.
对模切机模切加载过程进行分析,采用数学方法拟合了一条加载过程曲线,确定了肘杆机构可承受的最大模切压力值。
After the analysis of loading process, a loading curve is simulated by math method, which fixes on the most press value that can be endured by elbow-bar framework.
应用推荐