将图层混合模式设置为正片叠底。
根据适当的序列和模式设置标识符
Sets the identifier based on the appropriate sequence and the pattern
把默认登录模式设置为只历史。
成功将故障转移模式设置为“排队”。
通过利用一种新的内核模式设置特性加速了开机进程。
This speeds up the boot process by taking advantage of a new kernel mode setting feature.
要使用业务项实例,请将建模模式设置为中级或更高。
To use business item instances, set the modeling mode to intermediate or higher.
在本文中,我们只讨论以全分布模式设置Hadoop。
In this article, we will only cover setting up Hadoop in fully-distributed mode.
将图层模式设置为柔光,透明度设置为60%。
注意,上述的步骤1将项目的捕获模式设置为ON。
Note that Step 1 above sets up the project with capture mode ON.
将消息传递引擎集群添加到总线,并将数据库模式设置为正确值。
Add the messaging engine cluster to the bus and set the database schema to the correct value.
然后将这个图层的混合模式设置为叠加,并用蒙版圆滑转角。
Then set the layer to Overlay blending mode and use a mask to round off the corners.
通过用户界面把默认登录模式设置为只历史模式的步骤如下。
To configure the default login to history-only mode through the user interface, complete the following steps.
Hibernate还提供了第二种可以在查询中使用的抓取模式设置。
Hibernate also provides a second fetch mode setting you can use in queries.
要想以单独或伪分布模式设置Hadoop,请参考Hadoop的网站。
To set up Hadoop in standalone or pseudo-distributed mode, refer to the Hadoop Web site for reference.
要针对非受管模式设置属性,您就必须指定CICS服务器所需的所有属性。
To set the properties for non-managed mode, you must specify all properties required by your CICS server.
对内核引导过程和图像模式的一个有趣更改是基于内核的模式设置(KMS)。
An interesting cosmetic change to the kernel boot process and graphics mode is called the kernel-based mode setting (KMS).
请注意,托管模式设置初始化需要占用一分钟左右的时间,特别是在第一次运行时。
Note that it takes a minute or so for the hosted mode setup to initialize, especially when run for the first time.
现在将水彩图层的透明度减少到70%左右,将覆盖模式设置为混合模式。
Now decrease the opacity of the watercolor layer to about 70% and set its blend mode to Overlay.
要缓冲模式,需要一种允许您编译模式并将模式设置在解析器上的API。
To cache schemas, you need an API that allows you to compile schemas and set those on the parser.
步骤4。将图层模式设置为“叠加”,并调整一下“图层1”的填充不透明度。
Step 4. Set the blend mode to 'Overlay' and change the fill opacity on 'Layout 1'.
将会话的read - levelpassthrough模式设置为FORCE。
Set the read-level passthrough mode to FORCE for the session.
将下一个事务的read - levelpassthrough模式设置为FORCE。
Set the read-level passthrough mode to FORCE for the next transaction.
选择Currentschema设置,可以看到连接所用的用户ID用作当前的模式设置。
Select current schema setting and observe that your userID on the connection is used for the current schema setting.
我们将这个图层的模式设置为柔光,50%的不透明度。最后我们得到了一个很好的光照效果。
We set this latest layer to Soft light and 50% Opacity, and finally we have a nice lighting effect.
在定义人工任务时,可以使用一个新属性把所有权模式设置为single或parallel,见图1。
When defining a human task, a new attribute enables you to set the ownership pattern to single or parallel, as shown in Figure 1.
vga=0x301将图形模式设置为 640x480(请参阅Howto中的 5.3 节)。
vga=0x301 sets up the graphics as 640x480 (see Section 5.3 of the Howto).
主要内容如下: (1)设计了恒流源模块、激励测量模式设置模块、信号检测模块及采集模块。
The main work is as follows:(1) We design a source current module, a pattern-setting module, a measure module and a acquire module.
确保在消息处理期间输入节点的转换模式设置为“NO”,输出节点设置为“Automatic”。
Ensure transaction mode is set to 'no' for input nodes and 'Automatic' for output nodes during message processing.
确保在消息处理期间输入节点的转换模式设置为“NO”,输出节点设置为“Automatic”。
Ensure transaction mode is set to 'no' for input nodes and 'Automatic' for output nodes during message processing.
应用推荐