所有压底模图印被仔细检查和确认；
All pressing negatives are to be carefully checked & confirmed;
负责产品图、模图、模胚图的审核，零件图的批准。
Responsible for review of product drawing, mould block drawing and mould drawing, approve part drawing.
若需再次评审，则按以上模图初稿评审要求重新组织评审。
If needed, organize a new review meeting according to above requirements for mould first draft review.
在计算与分析的基础上，给出了常用参数范围内的剪应力计算诺模图。
Based on the calculation and analysis, the abac for shearing stress calculation in the range of normal parameter is obtained.
基于气田的物质平衡方程序，在本文中提供了确定定容封闭气田地质储量的诺模图。
A nomograph for determining gas in place (GIP) in a closed gas field is presented in this paper based on the material balance equation.
通过分析所得模图和相图的典型特征，得到舰船非线性横摇幅值和频率等动力学特性。
The dynamic characters about amplitude and frequency of ship nonlinear roll under typical wave parameters were obtained.
混沌方法人为参与程度低，稳定性强，可以方便准确地绘出平板各种颤振参数的诺模图。
The chaotic search method needs little manipulation and possesses superior robustness and the nomograms of various flutter parameters of flat plate can be plotted conveniently and accurately.
介绍利用计算机绘制进模图的原理和方法，使得绘制出的诺模图比手工绘制出的图更加精确和方便。
This paper put forward a method of drawing NOMOGRAPHY by the computer, also gives a mathematics principle of drawing graph and procedure circle.
本文是分析当零件上具有一般位置平面的结构要素时，如何设计诺模图以及怎样应用所设计的诺模图来绘制这些结构要素的基本视图。
Nomographs can be designed on the basis of equations used for projection transformation. This paper describes how to design and apply nomographs in constructing the basic views o…
最后，论文以ARAPA原模图ldpc码为分量码，结合多级编码调制(MLC)技术，设计了一种兼顾带宽和功率效率的编码调制系统。
Finally, a multilevel coding (MLC) scheme with ARAPA protograph LDPC codes as component codes is designed. This scheme takes both bandwidth and power efficiency into account.
研究LDPC码的原模图设计及构造方法，给出LDPC码的子类：RA码、IRA码、ARA码及其嵌套码的原模图表示、编码结构及阈值特性。
RA codes, IRA codes, ARA codes and its nested codes, which are the subclasses of LDPC codes, their protographs, encoding structures and threshold characteristics are given.
在基本编辑模式中，图9和图10中的流程模型看起来是一模一样的。
In the basic editing mode, the process models in Figures 9 and 10 look identical.
我使用平面图和剖面图，这些给我基本的体量信息，从中可以建立我的草模。
I used a plan and section which gave me basic volume information from which I could develop my massing.
从图3- 12可以看出，共模电流(ICM)是从电源线经过电源变压器通过电容耦合(CCOUPLING)而产生的。
As shown in Figure 3-12, common - mode current (ICM) is caused by capacitive coupling (CCOUPLING) from the power line through the power transformer.
本文研究了基于最大互信息和图象梯度组合的人脑CT与MRI多模医学图象配准算法。
This paper aims to research registration of CT and MRI images of caput based on gradient and normalized maximization mutual information method.
全息图转移到基板发生在这一点烫金或模切到所选材料的全息图案。
Transferring the hologram onto a substrate occurs at this point by hot stamping or die cutting the hologram onto the selected material.
图1显示了充模时间和压力之间的关系。
Fig 1 shows a typical relationship between filling time and pressure to fill.
图1所示为一热冲压平面结合模具的公模简图。
Figure 1 shows the male die of a hot extrusion planar combined die.
包括表面波、单模、多模辐射，辐射角，辐射方向图等等。
Including surface wave, singlemode, multimode radiation, the radiation Angle, radiation pattern and so on.
电力系统图模一体化系统是电力系统分析、计算、设计、监控、管理等诸多应用系统实现图形可视化的基础。
Power system chart-module integration system is the basis of the visualized power system analysis, calculation, design, monitoring, management, among many other applications.
模体标志图显示出分布在此抗体识别位点周围的氨基酸。
The Motif Logo shows the amino acid distributions around the sites recognized by the antibody.
分析了支座激励与响应之间的关系，利用图模法推导出蜂窝纸板-质量系统的振动传递率公式。
The relationship between the base excitation and the system response was analyzed, the transmissibility equation of the honeycomb paperboard-mass system was formulated using graph model.
螺纹模头(图10)，机械运行时塑料材料是围绕着导体延压出来。
The tubing die, Figure 10, extrudes plastic tubing concentrically around the emerging conductor.
公司欢迎您的光临指导、考察，欢迎您的来电垂询，来图定制各种规格塑模。华丰期待与您真诚的合作！
The company welcomes you to direct, investigate, call and make order the various plastic moulds. Huafeng wishes to cooperate faithfully with you!
近年来基于最大互信息法的多模医学图象配准已成为医学图象处理领域的热点。
In these years, multimodality medical image registration based on maximization of mutual information has been popular in medical image processing fields.
分析了文件夹手柄多工位级进模的冲压工艺，设计了排样图及模具结构。
The stamping technology of multi position progressive die of handle of file clip was analyzed. The layout and mould structure were designed.
介绍安装板进模的模具结构，重点介绍其排样图及主要零件的设计，同时提供一些经验数据。
The die structure of progressive die of assembled panel is introduced. The strip layout and the design of main parts are also analyzed. Some reference data are also provided.
压力模头(图9)，当模头与导体连接时，塑料仍然受到模头的压力。
In the pressure die, Figure 9, the plastic is still under some pressure inside the die when it contacts the conductor.
从亥姆霍兹方程出发，导出了自聚焦光纤中传导模在圆柱坐标系中的场分布形式，并给出了几个低阶模的分布图。
The propagation modes in selfco fiber, which features the laguerre Gauss distributions, are derived by solving the helmholtz wave equation incylindrical coordinates.
零部件图及组立图的做成，试模的跟进，全程参与了公司体系的建立等等。
I am responsible for working out parts drawing and assembly drawing as well as tracing mold testing. I have taken part in the whole company's system establishment course.
应用推荐