理想的折叠及校正设计确保精美产品。
Well design for folding with corrector to ensure fine production.
对控制系统的校正设计方法进行了简单的介绍；
This paper briefly introduces design methods of corrector on control systems;
本文对双闭环泵控式速度控制系统提供了一种简便而有效的分析方法及校正设计。
This paper advances a simple and effective analytic method and compensating design for the velocity control system of a double closed loop pump control.
张力控制系统是参数时变、干扰较多的系统，采用串联校正设计方法很难得到希望的动态性能。
Tension control system is a time? Varying parameter system with disturbances, it is difficult to obtain desirable dynamic performance by means of series tuning design.
介绍了某机载相机伺服系统，对其工作原理、基本结构、控制方案、校正设计等进行了分析探讨。
An airborne camera servo system is introduced, and the principle, structure, control scheme, drive technology of the system are analyzed.
本文根据最优闭环传递函数，论述最优控制器的设计，对过程控制系统与仪表装置的校正设计有参考价值。
Based on the optimal closed-loop transfer function, a new design method of optimal controller is proposed; which can be widely used to a process control sys-tem and for instrumental calibration.
温度闭环校正设计可以减缓失效积累损害的正反馈，同时使系统可以应对突发过温等情况，有效增加了系统可靠性以及使用寿命。
In the meanwhile, with this loop the system can deal with unexpected over temperature situation, and can also increase the system reliability and life effectively.
对话框实际上显示了元素的时期，这些元素提供了潜在性冲突可能发生的地方的反馈，以在设计阶段的早期时间内就将其校正过来。
The dialog visually shows the period of the elements providing feedback where potential conflicts might occur to correct them early in the design phase.
当我测试的时候，我花大约5%的时间查看覆盖率结果，重新考虑我的测试用例设计，并编写一些新的测试用例校正我的错误。
When I test, I spend somewhat less than 5% of my time looking at coverage results, rethinking my test design, and writing some new tests to correct my mistakes.
这个电压校正器的控制精度比设计的低得多。
The control precision of the voltage corrector is much lower than designed.
一座附属于阿拉巴马地区的大学的建筑学校正想用通过设计一种只花费两万美元的房屋建筑设计来解决经济适用房的问题。
An architectural school affiliated with a university in Alabama is tackling the problem of affordable housing by designing a house that can be built for $20, 000.
用校正过的数据再进行模拟、分析，直至最终实现设计和操作的最优化。
Then simulation and analysis are performed iteratively until optimum design and operation conditions are retrieved.
本设计为兼顾模数转换器的速度和精度，采用数字校正技术，以每级1.5 位的9 级流水线结构实现。
The converter has a good tradeoff between conversion speed and conversion precision. It is a 1.5-bit per stage with 9 stage and digital correction technique.
本文以实际的焦炉煤气集气系统压力过程为对象，介绍一神极点配置自校正调节器设计的新方法。
By the practical pressure process of coke oven gas collection system as object, a new method of to design pole placement self-tuning regulator is introduced in the paper.
通过对该方法灵活运用，本文用较少的代价完成了频率测量及校正系统的设计，并对该系统进行了性能测试。
In this paper, the design of the frequency measurement and correcting system can be achieved with less cost, and it also offered the system performance test.
第5章介绍了模型应用系统下的模型校正子系统的设计与实现。
In chapter 5, we recount the design and realizing of subsystem of model correcting.
本设计利用超前校正原理，最终满足对控制系统性能指标开环放大系数、相角裕量、截止角频率的要求。
This design is the use of leading correction principle, finally meet the performance index of a control system open loop gain, phase margin, angular frequency requirements.
重点讨论了减振台的结构设计和自动水平校正的机理。
The paper mainly discuss the structural design of vibration reduction table and its self-adjusting mechanism toward horizontal.
为实现电子束曝光机扫描场的线性畸变校正，设计了图形发生器的成像系统，该系统包括硬件和软件两部分。
An imaging system of pattern generator was designed to correct linear distortion of scanning field of ane-beam lithography system, which was composed of both hardware and software.
系统具有树种校正功能、温度补偿功能、双对数曲线计算、历史趋势图设计等功能。
The system possesses species correction function, temperature compensation function, double logarithm curve calculation and history tendency chart design function.
本文提出了基于M68H08系列mcu的血糖测试样片校正系统的设计方案，并对其加以实现。
The paper has provided the design scheme of correction system for blood sugar test papers on M68H08 MCU, and has implemented it.
这些公式适用于单级及多级的串联超前、滞后以及滞后——超前等各种校正器的设计。
These formula are suitable for various designs of correctors with single -, multi-stage series in leading, lagging and lagging-leading.
分析了对PIN开关实现开关控制、RFSTC控制、STC校正控制的原理和设计方法，并给出了电路模块的实施框图。
In this article, we introduce and analyse the principles and design methods of PIN switch, RFSTC and STC adjusting, and give block diagram of the controlling circuit module.
在此基础上设计了它们的自校正预报器(STP)和自校正控制器(STC)。
On the basis self tuning predictor (STP) and self tuning controller (STC) are designed.
结合共轭梯度法，借助于MATLAB软件，提出一种控制系统校正环节优化设计的新方法。
A new method of optimisation design for the correction element in control system is stated by combining the conjugate gradient method and using MATLAB software.
描述了系统工作原理，给出了系统的硬件配置、SIWAREX U校正以及PLC软件设计。
The working principle and hardware configuration of the system, calibration of SIWAREX u, and PLC software were introduced.
设计自校正PID调节器的方法有多种。
There are many methods to design self-tuning PID controllers.
同时又设计了模糊自校正控制，进一步提高控制系统的控制品质。
At the same time the fuzzy correct control is actualized to further improve the character of.
同时又设计了模糊自校正控制，进一步提高控制系统的控制品质。
At the same time the fuzzy correct control is actualized to further improve the character of.
应用推荐