我们可以改做三板模吗？
板模板采用组合钢模，在组拼时模板缝间夹海绵条。
Combined steel form will be used for slab form, and sponge strip shall be used for the form joint during matching.
本文以BI型两板模为例介绍该系统的组成和设计原理。
With two BI template moulds as example, the structure and design principle of this system are described in this paper.
三板模；点浇口；模外定距分型；定模限位顶出；模具结构。
Three-plate mold; Pointed gate; Mold ranging parting; Restricted ejector of fixed-die; Mold structure.
分析塑料熔体在板模机头中的流动状况，并给出板模机头模唇设计方法。
The flow condition of plastic melt in the extrusion die is analysed in this paper, and the design method of the die lip-length for plastic plate extrusion is also given.
分析了冷凝器固定板的工艺性，介绍了该零件弯曲成形模的结构特点和工作过程。
The technological property of the fixing plate of the condenser was analyzed. The structure characteristics and working process of the bending die for forming the part were introduced.
分析上支座加强板的成形工艺，并着重介绍成形工艺中的冲孔模的三维设计。
On the analysis of the forming process of the reinforcing plate, introduced the forming process and the 3d design of piercing die.
特有设定构造，附微调保护装置，灵活调设裁断高度和裁断力度，能延长刀模和裁断板的使用寿命。
Specially set structure and attach fine-adjustment protection device, flexible adjustments height and force of cutting, can prolong service life of cutting die and cutting rubber board.
介绍安装板进模的模具结构，重点介绍其排样图及主要零件的设计，同时提供一些经验数据。
The die structure of progressive die of assembled panel is introduced. The strip layout and the design of main parts are also analyzed. Some reference data are also provided.
利用作者已开发的汽车覆盖件成形预测系统，针对一汽车车门内板的成形过程进行了模拟分析，并对其在试模过程中可能出现的破裂问题进行了预测。
A forming process of the inner panel of automobile door was simulated by means of a developed prediction system. The cracking prediction of the panel during its forming process was given.
店内深处，店家桌子上方的告示板一角钉着一张宝丽来照片，和大卫给我看过的那张一模一样。
In the back of the shop, tacked in the corner of a bulletin board over the owner's desk, was a Polaroid picture just like the one David had shown me.
包装行业：雕刻印刷橡胶板、塑料板、双层板、刀模切刀板等。
Packaging industry: printing rubber plate engraving, plastic plates, double plates, die cutter cutting board.
水火弯板是钢板无模成型工艺中一项极具特色的技术，目前广泛应用于造船生产中。
The line heating, a very special technology in steel plate forming process, has a broad application in the shipyard to create cured surface of ship structure.
介绍了空调机换热器端板的结构特点，对其几种产品进行了工艺分析，在此基础上设计了端板冲孔模。
Characteristics of end board of heat exchanger of air conditioner have been introduced with technology analysis of several products and introduction of structure features of piercing die.
但最根本的应该是在印刷电路板设计、元器件布置和连接线的安排上下功夫，抑制共模骚扰源的产生。
But most attention should be put on the PCB design, elements position and line connection, which can suppress the source of the common mode disturbance.
本文介绍了在印刷线路板的冲孔模中，采用的液压卸料装置。
In the punching die of printed-circuit boards, a hydraulic stripper is used.
用脉冲激光切割模切板使切缝和刀体保持良好的接触，提高了模切板的刚度、强度及使用寿命。
The pulse laser cutting is a new working process, which can make the seam to contact better with the body of knife, so the strength, life and rigidity of the die board have risen.
建立了双曲率蜂窝夹层板在“点阵钉模、真空负压”条件下成形的有限元分析模型。
A finite element model was established to simulate the forming process of double curvature honeycomb sandwich panel under the conditions of "nails die, vacuum".
介绍大屏幕彩色电视机主印制板多小孔复合模的模具结构、设计参数、材料的选用和制造工艺等。
The structural design, design parameters, material chosen and manufacture process of multi-pinhole compound die of main printed circuit board for large screen color TV are introduced.
元件，该元件固定到一板状组件上的方法，组件总成及模扣。
Element, method of attaching element to plate-like component, assembly and die button.
介绍了多工位数控冲床用百页窗模具的设计，重点介绍了下装凸模、上装镶拼凹模及卸料板的设计和计算方法。
This article introduces the design of louver tooling for turret punch press, mainly focusing on the design and calculation of die, punch body and stripper plate.
公路桥梁预制钢筋混凝土板梁施工中，底模的制作及脱模是关键。
Fabricating and demoulding of the base mould is a key during the course of construction for precast plate girder of highway bridge.
对基模和高阶高斯光束通过位相板后的变化作了详细的计算分析。
Changes in fundamental and higher order Gaussian beams propagating through a phase plate have been studied numerically in detail.
根据羊龙潭水库地质条件，选用振动沉模防渗板墙来进行防渗加固。
The vibration and sinking-mould plank wall of seepage prevention is a new technique to mould continuous wall of seepage prevention underground by injecting slurry and sinking mould.
分析了液压卸料装置的结构及应用。说明了液压卸料装置在印刷线路板冲孔模中有很好的应用前景。
This paper analyzes the structure and its application of the stripper and shows a very good perspective application of the hydraulic stripper in the punching die of printed-circuit boards.
模具为倒装复合模，工件开始放在定位板上，冲压完成后工件从上端由推件装置推出。
Die for Flip composite mold, started on the workpiece positioning plate, stamping the completion of the workpiece from the top by pushing the device launched.
运用有限元方法分析了模切板刀片的复合弯曲成形，对成形过程中的回弹进行了研究。
The finite element analysis of the compound bending forming process is done for knives of the template. The spring back in the forming procedure is investigated.
然后让压模接触一种合适的“纸张”——在玻璃、矽或高分子板上的金薄膜。
The stamp is then brought into contact with an appropriate sheet of "paper" -a thin film of gold on a glass, silicon or polymer plate.
在滚锻时，圆的或是扁平的棒料放在模辊之间缩小横截面增加长度制成诸如轮轴、板簧之类的零件。
Roll forgings. In roll forging, a bar stock, round or flat is placed between die rollers which reduces the cross-section and increases the length to form parts such as axles, leaf springs etc.
在滚锻时，圆的或是扁平的棒料放在模辊之间缩小横截面增加长度制成诸如轮轴、板簧之类的零件。
Roll forgings. In roll forging, a bar stock, round or flat is placed between die rollers which reduces the cross-section and increases the length to form parts such as axles, leaf springs etc.
应用推荐