折弯件的圆弧是平滑过渡的，外形美观，不影响管材强度。
The arc on the bended pipe has smooth transition, making a better appearance while the strength of the pipe will not be affected.
在更旧的系统上工作时，程序员和操作工必须要清楚一个零件如何被合适地折弯，保证生产效率，并且避免发生碰撞。
Working with an older system, the programmer and operator have to be aware how a part should be properly bent to ensure efficiency and avoid collisions.
切割完毕之后，有的需要去毛刺，有点需要折弯，有的平板零件只需直接送去喷涂，装配，或者直接打包。
After cutting, some may need to be deburred, some need to be bent; while other flat parts are just sent directly to powder coating, assembly, or directly to packaging.
但是一旦一个零件被编好程序，自动化折弯单元就开始运转，毫不停歇，毫无抱怨，效率显著。
Once a part has been programmed, however, the automated bending cell is ready to run—no breaks, no excuses.
以前为了生产区区5000个零件，却要花费几天时间来教会一个机器人进行几步简单的折弯操作的日子已经远去了。
The days of spending several days to teach a robot how to do a couple of simple bends for a run of 5, 000 parts is over.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。提高了产品质量以及生产效率。
The bending and pressing convex forming compound die for locking spring is designed, the die structure and pressing process are introduced, the product quality and production efficiency are improved.
通过对转角拉扣五金零件的工艺分析，设计了一款切折弯曲落料级进模，同时对模具工作过程作了介绍。
Through analyzing the forming process of the comer pull buckle part, designed a cutting-bending-blanking progressive die. And introduced die working principle.
另外，在折弯、抗扭强度相同时，重量较轻，所以也广泛用于制造机械零件和工程结构。
In addition, the utility model has the advantages of light weight and bending strength, and is widely used for manufacturing mechanical parts and engineering structures.
希望是如此神奇的一件事情。它被折弯，被扭曲，有时甚至被阴影所遮挡。
Hope is such a marvelous thing. It bends, it twists, it sometime shades.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。
The bending and pressing convex forming compound die for locking spring is designed, the die structure and pressing process are introduced, the product quality and production efficiency are improved.
高低压开关柜及各种配电箱，采用大量的薄钢板折弯零件。
A lot of thin steel sheet bent parts are applied in high and low-voltage switchgear cabinets and various kinds of power distribution boxes.
该系列自卸车选用国际外优良名牌液压件、副车架和车厢纵梁均采用优良锰板焊接和锰板折弯制作而成。
This series dump truck adopts quality hydraulic components, sub-chassis and carriage. Longitudinal beam adopts is made of quality manganese plfore jointing and folding.
尺寸小折弯复杂的零件一直都是模具设计中的难点。
The parts with small size and complex fold are always to be the difficulties during the die design.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。
The structure and design method of typical bending slide block using in punching die were introduced.
针对锁紧片零件，设计了折弯压凸复合模，并介绍了模具结构和工作过程。
The structure and design method of typical bending slide block using in punching die were introduced.
应用推荐