因为制作过程中软性基板可能会发生弯曲或位移，它要与一片刚性玻璃临时粘合在一起。
Because the flexible material can curl or shift during this process, it's bonded temporarily to a rigid piece of glass.
文中考虑了竖向力对群桩刚度的影响以及桩基承台水平位移与弯曲、扭转位移的耦合作用。
The effect of the vertical force on the pier stiffness and the interaction among the level, bending and torsion displacement is also studied.
这些支撑，除运载来自货物等等的局部载重之外，也保持甲板和底部避免由纵向船体纵桁弯曲造成的相互位移。
These supports, in addition to carrying local loads from cargo, etc, serve to keep the deck and bottom from moving toward each other as a result of longitudinal bending of the hull girder.
基于三阶折线位移模型，利用虚功原理导出了含初始平面应力的层合复合材料板的弯曲理论。
Based on the third order zigzag displacement model, a bending theory for laminated composite plates in an initially stressed state is derived by use of the principle of virtual work.
片岩斜坡中弯曲倾倒变形是通过密集的片理上逐层剪切位移实现的。
The bending and toppling deformation in slopes of mica quartz schist occurs due to shear displacement slice by slice of schist with concentrated schistosities.
利用初始函数法，提出一种类似三阶位移模型的板弯曲方程新模型。
A new model of plate bending Similar to the model of three-order displacement is proposed by means of the method of initial functions.
对该模型施加适当的约束和载荷，通过预前共轭梯度法，计算得到了轴类零件在常见工况-弯曲和扭转载荷作用下的位移、应力、应变等力学特性。
Results of displacement, stress and strain of the shaft under the common loads of bend and torsion are obtained by Pre-condition conjugate gradient method.
本文应用功的互等定理，给出了弯曲矩形板的广义位移解及其边界值。
In this paper, the reciprocal theorem is applied to give the generalized displacement solution and its boundary values of the bending rectangular plate.
文中推导了位移及力的迭代公式，其中考虑了多阶剪力墙的弯曲变形及剪切变形。
When displacement and force iterative formulae are derived, the bending deformation and shearing deformation are taken into account.
研究了四点弯曲型试件在各种类型载荷作用下的裂纹面位移，并考虑了裂纹尖端塑性区对它的影响。
A crack surface displacement of four-point-bend specimen under three types of loading is studied in this paper.
本文利用瑞利原理，推导了新型弯曲圆盘换能器模型在边缘夹持和边缘简支两种边界条件下的位移振动分布曲线。
Using Reyleigh method, this paper deduced the vibration and displacement curve basing on the edge strengthening and edge support boundary conditions.
计算了整个激光弯曲成形过程中温度场、应力场和位移场的分布。
The temperature field, the stress field and the displacement field of steel plate during laser bending process were calculated.
本文建立了一个梁单元位移算子的新概念，并提供一种梁平面弯曲变形的梁单元位移算子求变形的计算方法。
A new concept on the displacement operator for beam unit is established, and a method of calculating the deflection Angle of beam unit is then provided.
应用一种新的力学计算方法——随机位移法来分析小挠度薄板弯曲问题。
A new mechanical method, random displacement method, was used to analyse bending plates.
在弯曲变形的前期，载荷和位移曲线都成线性变化，干态试样在载荷达到峰值之前会出现小的波动。
The load and displacement curves is linear at the early stages of the flexural deformation, the dry samples have a little fluctuation before reach the load peak.
通过实验研究，分析了两种不同性能材料空心球在作为夹芯梁芯材时，梁弯曲的载荷-位移曲线的特点，另外对于结构的破坏进行了简单的力学分析。
Then we discuss the characteristics of the force-displacement curve of the sandwich beam, and finally give a simple mechanical analysis on the failure of the structures.
将电子散斑测量离面位移的光路引入到高弹性连轴器挠性杆的横向弯曲变形测量中。
The out-plane route of ESPI was introduced for the displacement measurement of flexible lever.
通过前摆转向的多步态仿真游动实验，解析了鱼体柔性段弧长和相对弯曲度对质心轨迹、转动惯量、力矩、转动角位移及最大转动角速度的影响，提出了有效提高鱼形机器人快速转向性能的方法。
Through the multi-gait simulations of forward-oscillation turn, some effects of the length and the curvature of the flexible fish body on the fast-turn parameters, including track of center of…
通过前摆转向的多步态仿真游动实验，解析了鱼体柔性段弧长和相对弯曲度对质心轨迹、转动惯量、力矩、转动角位移及最大转动角速度的影响，提出了有效提高鱼形机器人快速转向性能的方法。
Through the multi-gait simulations of forward-oscillation turn, some effects of the length and the curvature of the flexible fish body on the fast-turn parameters, including track of center of…
应用推荐