平行度为1的作业是序列作业。
A job that is running with one degree of parallelism is a sequential job.
整个合模过程模板精确的平行度。
测量直线度、平行度和垂直度。
测得的平行度较好，可供参考。
这些线的平行度不如那些线。
该原理可扩展到其他平行度误差的评定。
This principle can be extended to other evaluation of parallelism errors.
SHPB系统端面平行度加工要求分析。
Analysis of parallelism requirement for bar ends in SHPB system.
工件被磁力拉低，适合与达到高平行度。
Wordpiece is pulled down by magnetic forces. Surtable for reaching high parallelity.
介绍了用五棱镜法检测大口径光束平行度的原理。
The detection concept for large diameter beam parallelism with penta prism is introduced.
提出了用于改善抛光平行度的偏心分布载荷技术。
The technique of eccentrically distributed loading for the improvement of parallelism in polishing is proposed.
孔系之间的平行度误差，会影响齿轮的啮合质量。
Holes in parallel between the degree of error will affect the quality of the meshing gears.
在不增加啮合齿向误差的前提下，合理给定支承平行度要求。
Under the precondition of an absence of increase in gear mesh error a rational support parallelism can be set.
基于数字图像处理技术，提出大型轴类工件平行度测量方法。
The method of measuring the parallelism for large-scale shafts based on digital image processing was proposed.
由于模板平行度好，变形小和使用线性导轨，可有效保护模具。
Mold protection thanks to precise platen parallelism, minimal platen deflection and linear guides.
介绍一种根据出射光平行度要求计算斜方棱镜面形误差的方法。
A calculation method to calculate the surface shape error of rhombic prism according to parallelism demand of emergent beam is introduced.
液压控制齿轮调模装置，操作简单，稳定保持头板及中板之平行度；
Mould adjustment system is drive by hydraulic controlled gear transmission, which is easy for operation and can keep parallelity between head plate and middle platen.
文章提出了一种新的检测方法即用数字波面干涉仪检测平晶的平行度。
A new laser interferometer method is presented and used to quick measurement of parallelism of optical flat.
本文研究的是一个测试轴瓦高出度及轴瓦对口面平行度的虚拟测试系统。
This paper is focused on the virtual testing system of bearing bush for depth of parallelism and height.
仪器还可测量晶体材料折射率均匀性、晶体元件面形、角度、平行度等。
This instrument can also measure the refractive-index homogeneity, the flatness, the Angle error, the wedge Angle of crystal element.
本文讨论了一种用于大型工件平行度、垂直度测量的新方法及其测量系统。
In this paper a new method and apparatus with laser measurement system for measuring parallelism and perpendicularity of large workpieces are discussed.
提出了线对线平行度误差定向最小区域评定的数学模型及其微机处理程序。
Based on these, the microcomputer processing program to calculate the located minimum area value of the coaxiality error is designed.
本文介绍一种线、面对空间回转轴线平行度的测量方法，并进行了误差分析。
This paper introduces the measurement of the parallelisms for line and flat to space turning spindle axis. The measuring error is analysed also.
设计了用于测量输出为视频图像信号的多光轴光学系统的光轴平行度校正仪器。
The instrument for measuring the parallel of the multi?axis optical system with video output was designed.
下列署名的验船师认为曲柄肖不平行度超过允许值时会导致曲柄肖和轴承烧坏。
The undersigned did deem that if the non-parallelism of the crank pin exceeds permissible limitation, crank pin and bearing were caused to be burnt.
结构为四柱导向，上压式，双油缸加机械平衡系统，保证了上下工作台之间的平行度。
The structure is four - pillar guide, up - packing, doublecylinder and machine balancing system. ensures the parallelism of upper and lower working sides.
系统整体误差的主要来源为距离测量误差、时间测量误差以及光束不平行度产生的误差。
The entire system error is mainly caused by the length error and time error and light-beams non-parallelism.
系统整体误差的主要来源为距离测量误差、时间测量误差以及光束不平行度产生的误差。
The entirety system error sourced from the length error and time error and light-beams non-parallelism.
系统整体误差的主要来源为距离测量误差、时间测量误差以及光束不平行度产生的误差。
The entirety system error sourced from the length error and time error and light-beams non-parallelism.
应用推荐