在此基础上进行了相应的工艺实验研究。
烹饪工艺实验是烹饪类专业的主要实践教学环节。
The experiment is the main practical training for cuisine technology specialty.
工艺实验研究；
细长传动轴两端花键头进行了冷挤压加工分析与工艺实验。
An analysis on the cold extrusion process and a technological experiment were made for the two spline ends of a slim drive shaft.
工艺实验证明该系统能够较好地实现磨削温度的在线监测与预报。
It is proved by technological experiments that the monitoring system can better realize on line monitoring and forecasting for grinding arc temperature.
完成了以芭蕉、菠萝和糯米为原料的多菌共酵食醋酿造工艺实验。
In this paper, a method of producing vinegar from banana, pineapple and glutinous rice by multi microorganism fermentation is introduced.
用新的缩分取样公式研究了提金工艺实验样品湿法分析金的准确性。
Furthermore, the accuracy of wet assay of gold in experimental sample was studied by means of new reduction sampling formula.
为了节约成本与生产顺利进行，采用冷挤压工艺方案进行工艺实验。
In order to reduce the cost and make smooth production, the cold technology is adopted to carry out the technical experiment.
工艺实验表明，本文所研制的ISSW可以满足点焊工艺设计基本要求。
ISSW developed here meets the basic requirements of spot welding procedure design from the results of mass tests.
本文基于工艺实验建立的萃取与反萃模型，作为过程模拟和设计的基础。
Process simulation and design were based on models of extraction and stripping developed experimentally.
将受力分布引入成形线圈设计，有效地提高了工艺实验中线圈的使用寿命。
Meanwhile, the introduction of the magnetic pressure distribution into the forming coil design brought an obvious improvement of the coil service life in technology experiments.
本文介绍了铀上离子镀铝使用的离子镀装置及离子镀工艺实验的主要结果。
The ion coating equipment and the technical experiment results for ion coating Al on uranium are described in this paper.
在氮化硅波导上进行的工艺实验表明，实验结果与理论分析有很好的一致性。
The experiment results on silicon nitride waveguide are in good agrement with the theoretical analysis.
给出各种不同的线宽和分离量之间的关系，并通过大量的工艺实验得到证实。
The relationship among different widths of lines as well as clearances is presented, and it has been proved by a lot of experiments.
提出一种新的玻璃管切割方法。介绍了加沙水刀切割玻璃管的工艺实验现象。
A new method for glass tube cutting is provided and the experimentation on glass tube cutting with abrasive water-jets is introduced.
通过南瓜多糖提取工艺实验，确定了浸提、活性炭脱色过程的较优工艺参数。
The Conditions of pumpkin polysaccharide production from pumpkin were studied. The optimum Conditions of extraction, Decolorization by active carbon were determined through the experiment.
上述分析为装置的性能改善以及微小孔振动钻削工艺实验奠定了一定的理论基础。
Above-mentioned analyses in this paper lay a theoretical basis for improving performance of the device and doing technologic experiments of vibration drilling.
由工艺实验得出了木糖醇悬浮液的过滤方程和干燥曲线，并对其特性进行了讨论。
The filtration equation and drying curve are obtained from process experiments. The Characteristics of the filtration and drying process are discussed.
此文用塑性泥作模拟材料，进行了压扭复合锻造和不对称V型砧拔长的工艺实验。
The experiments of twist-compression forging and unsymmetrical V-shape die forging are made using plasticine.
通过理论计算及工艺实验，证明了此理论的正确性，井已用于生产，其效果良好。
Through theoretic calculation and experiment, this proposal has been proved to be correct and has been used in production with a good result.
利用建立的系统模型设计了多机器人铝合金交流脉冲gtaw的悬空角焊工艺实验。
And a special welding technic experiment of aluminium AC pulse GTAW with robots was designed, too.
结合研究的成果，完成了对旋转椭球面和旋转抛物面等非球面工件的加工工艺实验。
Machining test, including turning rotary ellipse and rotary parabola, agrees well with researched conclusion.
通过工艺实验，对重组木和单板条平行胶合材(psl)的主要力学性能进行了研究。
The main mechanical properties of scrimber and Parallel Strand Lumber (PSL) were researched through technological test.
对干法再生出来的树脂再生砂进行制芯的工艺实验，实验标准按照生产上的要求来实行。
The technological experiment of reclaimed resin bounded sand produced through dry reclamation is made, the way of which is standard.
用微波能对食用菌二级种培养基进行袋装杀灭杂菌的工艺实验，以替代传统蒸煮灭菌的工艺。
The processing technology of microwave disinfection for the bagged second-generation culture medium of mushroom is investigated to displace the traditional steam disinfection.
研究了金属网栅结构参数对其光电特性的影响，并通过工艺实验结果测试，验证了分析计算成果。
The characteristic dimension and its effects on the optical and electrical performance of a metallic mesh are analyzed and tested with a set of craft experiments.
该方法经济简捷，可以代替大量的工艺实验实现对离心研磨技术参数的优化，从而提高生产效率。
The parameters of design and technology can be optimized economically and efficiently with the method so as to improve productivity.
通过TMCP工艺实验，研究了终轧温度和卷取温度对低碳锰钢力学性能和微观组织的影响规律。
The effects of processing parameters of TMCP, such as finish rolling temperature and coiling temperature on microstructure and mechanical properties of low CMn steel were studied by TMCP tests.
对铝型材进行化学砂面和阳极氧化复合工艺实验，探讨了复合工艺中各因素对鈻型材表面质量的影响。
Technology of chemical coursing and anodic oxidation for shaped al materials was studied. Vanous factors influencing the surface quality of shaped al materials are discussed.
简述了人体损伤机理和损伤指标，并介绍了按照亚洲人身材特点研制出的汽车正面碰撞工艺实验假人的结构特点。
The humans body damnification mechanism and index are briefly reported in this paper, and the automobile obverse impacting technics experiment dummy according to Asian stature is explained.
应用推荐