尾架主轴也锁定在一个类似的方式。
铸件中的小组是为金格里分度头和尾架的部分。
The middle group of castings are the parts for the Gingery dividing head and tailstock.
文中介绍了静压尾架的结构， 尾架孔加工工艺。
The paper introduces the construction of the tailstock and the machining process of the bore.
车床的最大的零件称床身，车头和尾架被紧固在相反末端的床身。
The largest part of the lathe is called the bed on which the headstock and the tailstock are fastened at opposite ends.
尾架：安装在床身导轨上，并沿此导轨纵向移动，以调整其工作位置。
The tail frame: installed in bed, and guide rail along the guide rail, adjusting to the longitudinal mobile work position.
车床的主要部件都装在具有导轨的床身上，刀架与尾架可沿着该导轨滑动。
All of the principal units of the lathe amounted on a bed having ways along which the carriage and tailstock travel.
尾架主要用来安装后顶尖，以支撑较长工件，也可安装钻头、铰刀等进行孔加工。
The frame is mainly used to after installation, to support a top attractions, also can install a bit, reamer hole processing, etc.
一个短的工作在主轴箱主轴上通过适当简单的卡盘无需使用尾架中心也许就能被转动。
A short work may be turned without using the dead center, by simply chucking it properly at the spindle of the headstock.
改善尾架与车架的搭接长度，将连接焊缝改为断续焊缝，从而有效地提高了车架的强度。
Also, improve the overlapped length of the tail frame and the frame and change the welding seam into intermittent seam, therefore the frame strength can be effectively increased.
改善尾架与车架的搭接长度，将连接焊缝改为断续焊缝，从而有效地提高了车架的强度。
Also, improve the overlapped length of the tail frame and the frame and change the welding seam into intermittent seam, therefore the frame strength...
一架楔尾飞机将由波音公司澳大利亚防务部门的人员在南澳大利亚的Woomera测试厂控制扫描鹰的行动。
A Wedgetail will take control of ScanEagles operated by Boeing Defence Australia personnel at Woomera Test Facility in South Australia.
结果表明：粘性耗散与塔架效应是引起尾涡变形的主要原因。
The result shows that viscidity dissipation and tower effect are main reasons of wake eddy distortion.
潜水电机壳体，包括机架，尾轴承架，法兰和罩盖总装，必须采用符合美国材料试验协会ASTM A - 48类别30标准的、密实的铸铁或更好的材料制造。
The submersible motor enclosure including frame, end brackets, flanges and cap assembly shall be constructed of close-grained cast iron, ASTM A-48, Class 30 or better.
顶部尾轴承架应该配置不锈钢吊环，应该能够支撑泵和电机的总重量的压力。
The top end bracket shall be fitted with a stainless steel lifting bail and shall be capable of supporting the combined weight of the pump and motor.
顶部尾轴承架应该配置吊环，应该能够支撑泵和电机的总重量四(4)倍的压力。
The top end bracket shall be fitted with a lifting bail and shall be capable of supporting four (4) times the combined weight of the pump and motor.
采用实验方法对某舰尾轴架进行动刚度测量，得到了前尾轴架和后尾轴架的横向动刚度曲线。
In the paper, the transverse dynamic stiffness curves of front shaft bracket and back shaft bracket of a ship were obtained by means of experiments.
分析尾轴架的动刚度曲线，可得到尾轴架结构的固有频率。
Analyses of these curves make the natural frequencies of the shaft brackets available.
从分析船舶尾轴架结构特点入手，介绍尾轴架工艺计算、工艺编制、产品生产过程及经验。
Starting from analyzing the structural properties of the Marine propeller shaft bracket, the authors introduce the technology calculation, design, process and their production experience.
介绍了在大批量定制生产和检测中所需使用的硬盘驱动架尾孔的机器视觉检测系统。
The paper presented a machine vision system for inspecting the diameter of the tail-hole in a hard disk driving shelf which was needed in mass customization production and inspection.
因此，船舶尾轴架结构的优化设计是一个很重要的问题。
Therefore, the optimizing of propeller shaft bracket is a very important issue.
对于丝锥尾方的加工可以采用磨削的方法，欲实现尾方加工过程的自动化，则磨削尾方专用机床的头架，因其动能是夹持工件，所以在加工过程中必须能自动分度。
The headstock of special purpose qrinder, which is used to hold workpieces, must be able to index automatically in the course of working to make the automatic grinding possible.
主要用于机车的摇枕、侧架、车钩及钩尾框等车辆件，同时也可清理类似尺寸的铸件和批量小件。
It is mainly used for the fittings of vehicles such as the swing bolster, side frame, coupler and coupler yokes, also for cleaning the castings and workpieces with the similar size.
现代级在它的尾甲板有一个小型飞行甲板和悬挂装置去容纳一架直升飞机。
The ship has a small flight deck and hanger on its stern deck to accommodate one helicopter.
现代级在它的尾甲板有一个小型飞行甲板和悬挂装置去容纳一架直升飞机。
The ship has a small flight deck and hanger on its stern deck to accommodate one helicopter.
应用推荐