镀金铜质加一颗小钻。
利用Dremel工具和小钻头，在塑料外壳上钻一个小孔。
With a Dremel and small bit, make a small hole in the plastic housing.
一只小鼹鼠，刚从洞里爬出来有点累了，正好发现了这支手套就钻了进去。里面是舒适和温暖的，而且大小正合适，它决定待在里面。
A mole, tired from tunneling along, discovered the mitten and burrowed inside. It was cozy and warm and just the right size, so he decided to stay.
不不，蚯蚓钻的没有这么小。
随着隧道施工机械化程度的提高，在特长小断面隧道工程中采用钻爆法掘进施工，其机械配套是制约掘进速度的重要条件。
With the development of mechanization and drill and blast in extra - long tunnels with a small section, the matching machinery is very important to driving speed.
实验表明，这种麻花钻的轴向力较普通麻花钻降低40%左右，扭矩降低20%左右，是一种切削力小、能耗低的麻花钻。
Experimental results show that the thrust of such a drill is decreased by about 40% as compared with that of a standard drill and the torque by about 20%.
螺杆钻具是其中的一项关键技术，其主要目的是研制满足侧钻中短半径水平井需要的小尺寸高造斜率的弯外壳螺杆钻具。
Small size bent housing screw drill with high build rate must be developed to meet the requirements of sidetracking the short to medium radius horizontal well.
他们使用小笤帚刷掉钻在作品缝隙中的雪屑。
They use small brooms to brush off snow caught in tiny holes.
弯壳体导向钻具的刚性大、变形小，因此可采用几何法来计算造斜率。
The bent-housing motor is relatively rigid, so the geometric method can be used to calculate the build angle rate of steerable motor.
带眼衬管一般用于小直径井筒或在不需对衬管注水泥(如层位封隔所要求)的储层内的侧钻。
Perforated liners typically are used in small-diameter wellbores or in sidetracks within the reservoir where there is no need for the liner to be cemented in place, as is required for zonal isolation.
分析了小直径深孔振动钻削对钻头的要求；设计了一种新型内排屑深孔钻头；分析了该钻头的结构和刃磨特点，进行了振动钻削试验。
Based on analyzing the demands of small-diameter deep-hole drill for vibration drilling, a new inner-chip removal drill was designed.
利用小直径麻花钻，改磨成“排孔钻”，并运用于技工学校的钳工专业技能培。
Make use of small diameter twist drill to change it into drill of wearing intersect holes and put it into the ability education of locksmith.
在后台连接到它的通过，最后钻具有线圈导线从它投射洞传递两个小螺栓手段。
The spool is attached to it by means of two small bolts passing through holes drilled in the end that has the coil wires projecting from it.
并分析了超声振动钻削装置设计中的一些关键技术问题，为在摇臂钻床上加工小直径深孔提供了一种新的工艺方法。
Some key techniques were analyzed when designed vibration device, and a new method was put forward for small-diameter deep holes.
并分析了超声振动钻削装置设计中的一些关键技术问题，为在摇臂钻床上加工小直径深孔提供了一种新的工艺途径。
Some key techniques were analyzed when designed vibration device, and a new method was afforded for small-diameter deep holes.
完成的井下工程参数随钻测试系统具有体积小、功耗低、抗振动和抗高温的优点。
The down-hole engineering parameters measure while drilling system has advantages of small in size, low power consumption, vibration resistance and high temperature resistance.
结合小型采石场设备简单、工艺相对落后的实际，介绍了一种采用硐室爆破替换其小直径钻眼爆破的方法，并对药室的布置及起爆网路作了阐述。
Considering the simple equipment and relatively lagged technique, a way of substituting coyote blasting for small diameter drifting blasting is introduced in this paper.
我想看有小碎钻的领带夹。
小尺寸螺杆压降受钻压影响比大尺寸螺杆大；
The effect of WOB to pressure drop of small geometry PDM is bigger than to large geometry PDM.
由于其刚性比钻铤少，和井壁接触面积小，也不容易形成压差卡钻。
Because its rigidity are less than the drill collar, less contact area with wall of a well, is also not easy to form differential pressure sticking.
系杆拱桥钢钻箱，具有“承受大吨位，适应小空间”的特点，给设计和制造增加了难度。
The steel anchor box of the tie ho arch bridge has the characteristics of carrying lug loads and fitting into a small space. This adds to the difficulties in design and production.
小的变动还可以，但是不要在墙上钻太多洞。
Little changes are OK, but please don't drill too many holes in the wall.
报告了我国近年来装备的标准化、可搬迁式、小模块化海洋钻修井机和海洋模块钻机等的技术特点及其应用现状。
The feature of modularized drilling rig and the difference between it and movable drilling rig are presented briefly in this paper.
我公司主导产品为钻尾螺丝系列(六角华司头、盘头、钮扣头、喇叭头、六角法兰头、小仔头等)，同时也生产干壁钉、纤维板钉和自攻钉等自攻类螺丝。
Our company is main products are series of drilling screws, and mean-while we also have sub production line for Drywall screw, Chipboard screw, and Tapping etc.
用于狭窄部位钻孔，扩孔攻丝等作业，具有重量轻，刚性好，钻削头边心距小等特点，且可反转。
Suitable for broaching or tapping in the cabined place. The air drill is light, good rigidity an can be used for drilling in reverse, aiguilles of which has short distance form the border to center.
用于狭窄部位钻孔，扩孔攻丝等作业，具有重量轻，刚性好，钻削头边心距小等特点，且可反转。
Suitable for broaching or tapping in the cabined place. The air drill is light, good rigidity an can be used for drilling in reverse, aiguilles of which has short distance form the border to center.
应用推荐