• 采用粉末冶金方法研制出金属陶瓷导板。

    A Copper-Tungsten ceramel guide has been developed by the powder metallurgy.

    youdao

  • 现场观察发现了钢板撞击精轧机组侧导板现象。

    The collision of steel strip with flipper guide was observed on finish rolling unit.

    youdao

  • 为此,研制了一种机械夹固式高铬钼抗磨铸铁组合导板。

    Therefore, a kind of mechanically fixed assemble guiding plate made of hi-Cr-Mo wear resistant cast iron was developed.

    youdao

  • 给出亚微米光栅型光导板的初始结构,并进行了误差分析。

    Finally, the initial structure of light guide plate with sub-micron gratings is given and the error is analyzed.

    youdao

  • 结论平面导板会造成下前牙牙根的吸收,但根吸收程度轻微。

    Conclusion Flat bite plate can cause root resorption of mandibular permanent incisors, but the root resorption is slight.

    youdao

  • 交互牵引结合固定平面导板是矫治下颌第一磨牙舌倾的有效方法。

    Clinical application of intermaxillary traction and fixed flat bite-plate could correct lingual inclination of mandibular molar effectively.

    youdao

  • 在导板优化基础上,对给定产品规格范围进行叶片宽度的优选设计。

    Further, the optimum design for blade width is carried out within the given range of product size.

    youdao

  • 本发明包括一个转筒和带动转筒旋转的驱动机构,转筒内 设有螺旋导板;

    The mechanical device comprises a rotary drum and a driving mechanism for driving the rotary drum to rotate, wherein the rotary drum is internally provided with a spiral guide plate;

    youdao

  • 纵向调节机构的纵向导板与定位板之间的连接方式可采用压紧连接或柱销式连接。

    The connection type between the vertical guide plate of the vertical adjusting mechanism and the positioning plate can adopt compression-fitting connection or dowel pin type connection.

    youdao

  • 侧导板、夹送辊、卷筒的位置控制对整个卷取区至关重要,直接影响卷取成功与否。

    The position control of side guider, pinch roll, and mandrel is very important for the whole coil area. It influences directly the success of coiling.

    youdao

  • 分割面的倾斜角被设为使从光源投射的光以基本上平行于光导板的板面的方向反射的角度。

    A slant Angle of the dividing surfaces is set to one at which the light projected from the light source is reflected in a direction substantially parallel with a plate of the light guide plate.

    youdao

  • 导板是线材轧机上的关键备件,要求有优良的耐磨性、抗断裂性、抗粘钢性和热冲击抗力。

    On wire - rod mill, the guide shoe is key spare parts to which, excellent wear - resistance, fracture - resistance, dead burning resistance and hot shock resistance are required.

    youdao

  • 结果深覆颌总矫正率72.2%,昼夜戴用该改良上颌平面导板组的深覆颌矫正率100%。

    Results The correction rate was 72.2% in total and 100% in therapy group.

    youdao

  • 渗水板上设置 有网状小孔,疏导板上设置有纵向的排水凹槽和与排水凹槽相垂直的连通凹槽。

    A net-shaped small hole is arranged on the seepage plate, and a longitudinal drainage groove and a groove which is vertically communicated with the drainage groove are arranged on the guided plate.

    youdao

  • 介绍了穿孔机导板系列三维参数化设计的基本过程,及运用计算机进行导板三维参数化设计的必要性和优越性。

    The basic process of three-dimensional parameterized design for the piercer guide board series has been described in this article as well as its necessity and superiority with CAD.

    youdao

  • 卷取机前侧导板的作用是把带钢对准轧制中心线送入夹送辊,并在进入夹送辊时导板夹持带钢以减少钢卷的塔形。

    The entry side guide of coilers aligns strips to the centerline of mills and then holds and sends them into pinch roll unit.

    youdao

  • 卷取机前侧导板的作用是把带钢对准轧制中心线送入夹送辊,并在进入夹送辊时导板夹持带钢以减少钢卷的塔形。

    The entry side guide of coilers aligns strips to the centerline of mills and then holds and sends them into pinch roll unit. By this way, the telescopicity of coils can be reduced significantly.

    youdao

  • 所述出风导板(5)一侧的壳体(1)上通过一铰接机构连接一可连通该出风导板(5)出风口的烘干支架(6)。

    A drying rack (6) communicating with the air outlet of the air outlet guide plate (5) is connected onto the shell (1) on one side of the air outlet guide plate (5) through a hinging mechanism.

    youdao

  • 为此,对该机组进行了改造:①拆除烟支上位控制装置和烟支下位传送装置及其组件;②设计加工并安装凹形导板和柔性搭链的支架。

    Therefore, the upper level controller and lower level conveyor and associated kits were dismantled, and a bracket for concave guide and flexible chain was installed.

    youdao

  • 摘要目的自主研究计算机辅助设计制造(CAD/CAM )导板的数字化设计方法,完成软件设计,创新性地加入了力学分析功能。

    Abstract : Objective To carry out independent research with the method of selfdesign CAD/CAM for implant guide.

    youdao

  • 摘要目的自主研究计算机辅助设计制造(CAD/CAM )导板的数字化设计方法,完成软件设计,创新性地加入了力学分析功能。

    Abstract : Objective To carry out independent research with the method of selfdesign CAD/CAM for implant guide.

    youdao

$firstVoiceSent
- 来自原声例句
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定
小调查
请问您想要如何调整此模块?

感谢您的反馈,我们会尽快进行适当修改!
进来说说原因吧 确定