板式换热器的密封垫片滑离了垫片槽。
Plate heat exchanger of sealing gasket slip off the gasket groove.
小心,不要损坏密封垫片。
这使得连接密封垫片。
符合IP65当正确安装使用的密封垫片供应。
IP65 when properly installed using the sealing gasket supplied.
预测了特定工况条件下CAS密封垫片的使用寿命。
The service life of CAS gasket could be predicted by this relationship.
水道的连接应衬有密封垫片。所有连接面都不应有应力。
Use sealed gasket in the water path. There isn't stress on all link surface.
当接触到热、橡胶密封垫片在传输变硬,这将导致泄漏。
When exposed to the heat, the rubber seals and gaskets inside the transmission hardens, which will cause leaks.
介绍了微机控制的电液伺服型密封垫片综合性能测试装置。
A test machine controlled by electro hydraulic servo and microcomputer for the comprehensive performance of sealing gaskets are introduced.
现主要产品有:塑料制品、密封垫片、填料三大系列,数百种产品。
Are the main products are: plastic products, gasket, packing three series, and hundreds of kinds of products.
机械式连接采用使用压盖的方法向密封垫片施加压力获得密封效果。
Mechanical joint in which sealing is obtained by applying pressure to the gasket by gland.
利用红宝石荧光测压方法,测量了压砧砧面以及密封垫片流变区内的压力分布。
The pressure distribution is determined by measuring the pressure at various points between the diamond cullet faces and the thin metal gasket using the ruby fluorescence method.
本阀可水平安装或垂直安装,安装时两法兰连接中间必须加密封垫片,然后锁紧螺栓。
It can be installed in horizontal or vertical. Sealing gasket must be put on the connected, then equably tight the bolt.
安装时请注意阀体上标注介质流向,两法兰连接时必需加密封垫片,然后均匀锁紧螺栓。
When installation, note flow direction of media of valve body. When connecting two flanges, add sealing mat. Then lock the bolt evenly.
安装时请注意阀体上标注介质流向,两法兰连接时必需加密封垫片,然后均匀锁紧螺栓。
Pay attention to the direction of medium in valve body. Add seal cushion between two flanges connection and screw down bolt.
本阀可水平安装或垂直安装,安装时两法兰联接中间必须加密封垫片,然后均匀锁紧螺栓。
The valve can be installed in horizontal or vertical. Add seal cushion between two flanges connection and screw down bolt.
由于膨胀机碳环密封后面的密封垫片在安装时未被充分压紧,使膨胀机机体及相应管道进油。
At installation, insufficient compression of the sealing pad behind the carbon ring seal of the expander results in oil entrance to expander body and to the corresponding pipeline.
通过计算实例,给出了压力容器设计中常见的焊接密封垫片连接结构的平盖设计的一种方法。
With the example, one method for designing flat cover with welded gasket commonly met in pressure vessel design was presented.
形密封:一般经过拆卸的O形密封应全部更换,对其它密封垫片等,只要没有破损,也可以复用。
O seal: usually the dismantled o seal should be changed totally, but the gasket, etc without breakage also can be reused.
微型扬声器防尘网,微型扬声器防水网,微型扬声器垫片,手机喇叭密封垫片,手机喇叭防尘网。
Micro speaker dust-proof net, Micro speaker water proof net, Small speaker gasket, phone speaker sealing gasket, phone speaker dust proof net.
为杜绝垫片材料加工制造过程中石棉粉尘引起的危害,应大力开发和应用推广不含石棉的密封垫片。
Developing, applying and expanding asbestos-free gaskets is proposed to prevent from the hazards caused by asbestos dust in production process for gaskets material.
试验研究了热氧老化对纤维增强橡胶基密封垫片主要性能的影响,结果表明垫片性能随老化而衰减。
The influence of thermal oxidizing aging on main performances of gasket was studied. Result indicates that performances of gasket are degenerated with aging of material.
通过对重油催化裂化装置中法兰泄漏原因的分析,提出了处理方法:将原石棉密封垫片改为波齿复合密封垫片。
By analyzing for the flange leakage on a heavy oil catalytic pyrolysis unit, the writer put forward a treatment method, i. e. to replace old asbestos gasket with a compound corrugated gasket.
处于板片有力支撑点包围中的密封垫片,能承受较大的流体冲击,不会泄漏,两次涂胶工艺保证了密封垫片牢固粘接。
Seal gaskets are closed in the support points of plates resist high press fluid impact and prevent leak out of fluids. Twice gelatinize technology make gasket firm connected.
打开锅炉的前后烟箱门,检查密封垫片及烟垢,以决定是否更换和清理,同时检修浇注的耐火混凝土和密封石棉垫(绳);
Open the smoke chamber of boiler; check the seal patch and smoke dirt to decide if it needs to clean up or replacement.
选用各种材质的固体金属,用机械切削加工而成的具有各种形式的金属密封垫片,适用于高温、高压及腐蚀性强的压力容器、阀门、气缸盖等的密封部位。
Machined from solid metals in a variety of shapes and are designed for high pressure, high temperature or highly corrosive applications by selecting the most suitable material and shapes.
选用各种材质的固体金属,用机械切削加工而成的具有各种形式的金属密封垫片,适用于高温、高压及腐蚀性强的压力容器、阀门、气缸盖等的密封部位。
Machined from solid metals in a variety of shapes and are designed for high pressure, high temperature or highly corrosive applications by selecting the most suitable material and shapes.
应用推荐