公路的定线测量工作传统上以外业为主。也就是说,定线测量工作的大部分时间和精力都花在现场的测量和观察上。
Traditionally, highway location practice has been field oriented, that is, the bulk of the location party's time and effort went to measurement and observation "on the ground".
论述了厦门湾附近水域船舶定线的目的。
The purpose of the ship routing in Xiamen bay and its adjacent waters is discussed.
探讨导线定线法及在输电线路测量中的应用。
The traverse surveying method and its application in measuring of power transmission line are discussed.
本文阐述在断裂构造地质地带的公路定线问题。
This paper investigates the highway alignment in the fault structural zone.
本文对铁路定线CAD系统开发的原理进行了介绍。
The principles of developing a railway location CAD system are discussed.
本文提出了便于复测和恢复定线的施工控制网的布设方法。
This paper proposes a new arrangement method of conduction control network which is easy to re-survey and reset control line.
工程定位放线测量(简称定线测量或放线)通常采用极坐标法。
The polar coordinate method is usually used into layout survey.
导线测量是一项精密而细致的工作,直接影响到路线的定线和高程系统的控制。
The orientation measurement is a precise and detailed job, and it affects directly the route alignment and the control of elevation system.
详细介绍了用公路路线上控制点坐标进行公路直线和曲线平面位置定线的数学模型。
This paper introduces the mathematical model for highway route alignment. This model can determine plan position of highway straight and curve by the control points.
为更好地满足沪杭磁悬浮工程全线施工定线的需要,提出了引用一种新型大地坐标系的设想。
In order to satisfy the requirement for the route location of the Shanghai-Hangzhou magnetic suspension project, a new form of geodetic coordinate system was proposed.
区域踏勘是定线测量的第一步。定线人员利用现有地形图,有时利用飞机对该区域进行探测。
Reconnaissance of the area as the first step, the locator, using available topographic maps and sometimes an airplane, explores the area.
在分析了传统的公路测设中选线、定线方法基础上,着重阐述了航空摄影测量在公路测设中的应用。
Based on the analysis of the traditional highway set-out alignment, the emphasis of the paper has been put on the application of aerial photogrammetry on the highway alignment.
承包商应负责对工程的所有部分正确定位,并应纠正在工程的位置、标高、尺寸或定线中的任何差错。
The Contractor shall be responsible for the correct positioning of all parts of the works, and shall rectify any error in the positions, levels, dimensions or alignment of the works.
设计主要包括公路选线定线、平面线形设计、纵断面设计、横断面设计、路基设计、路面设计等几个主要部分。
Design includes highway route alignment, Horizontal alignment design, Profile design, cross-sectional design, embankment design, road design, and several main parts.
本文针对传统的道路定线设计方法在立交定线设计中的不足与局限性,提出了一套用于道路、公路与立交设计的三维定线设计方法。
To improve the traditional road alignment designs for interchange design, the writer presents a 3-dimension alignment method for road, highway and interchange design.
滇西地区的构造格局具有一定的规律性,造山带与缝合线相间分布。
The tectonic situation in Western Yunnan is of certain regulation with the interlacing distribution of orogenic zone and seam.
因波浪线是不规则的曲线,所以计算机辅助绘图有一定的困难。
It is difficult for the computer to draw break lines, because they are irregular curves.
一定不要让金属线搭在一起。
一些智利人认为目前每月90美元的国家贫困线定的太低。
Some Chileans argue that the national poverty line, of $90 a month, is set too low.
显示器产生彩色像素点,我们的大脑给这些像素点一定的意义(如曲线、线、字幕和数字)。
Monitor produce colored dots, and these dots are given meanings (e.g. curves, lines, letters and Numbers) by our brains.
该方法充分利用了线阵CCD分辨率高的特点,并且具有一定的实用价值和应用前景。
This method USES linear array CCD characteristic with high resolution capacity and has certain practical value and application prospect.
介绍了尼龙66纺丝工艺对工业丝物理性能如线密度、强力、定负荷伸长率的影响。
The effects of spinning process on linear density, tenacity and elongation of Nylon 66 technical yarn were described.
钢帘线生产中,黄铜镀层存在一定缺陷。
Brass coating for steel tire cord has several disadvantages.
为开展电镀金刚石线锯的研究和生产提供了一定的指导。
This paper will provide a guidance for investigation and production of electroplated diamond wire saw.
在扫描次数一定的情况下,存在一个最优的累积线能量使弯曲角达到最大;
Under the constant bending times, the biggest bending angle can be obtained with an optimal accumulative line energy value.
冷却水质的优劣对高线盘条的质量有一定的影响,尤其是对表面质量影响较大。
Good and poor quality of cooling water have influence on wire rod, especially on surface quality.
建立了绕椭圆柱面以等角速度旋转,又以变速度上升的非定常螺距的螺旋线方程。
A helix equation of time-varying pitch is established, revolving elliptic cylinder as equal angular velocity and rising as variable velocity at the same time.
结果显示,一定的母材厚度和焊后热处理条件,使熔合线附近氢浓度峰值提高,从而使氢剥离倾向增大。
The results show that certain thickness of the base metal and the regime of heat treatment will increase the peak hydrogen concentration and promote the tendency of disbonding.
结果显示,一定的母材厚度和焊后热处理条件,使熔合线附近氢浓度峰值提高,从而使氢剥离倾向增大。
The results show that certain thickness of the base metal and the regime of heat treatment will increase the peak hydrogen concentration and promote the tendency of disbonding.
应用推荐