分析了缝纫机梭床磨损失效原因。
The causes of wear failure of the shuttle-race were analyzed.
分析退回物料的失效原因。
分析了铸造奥氏体耐热钢篦板失效原因。
The failure of grid plate made of casting austenite heat resistant steel was analyzed.
文章分析了失效原因并提出了建议与措施。
The causes of failure were analyzed and preventive measures were presented.
分析热水加热器的失效原因，并提出改进措施。
Analyze the reasons of failure for the water heater, and put forward the measures of improvement.
以压缩机管壳式冷却器为例，分析了其失效原因。
Take compressor's intercooler for example, main reasons of failure is analyzed.
采用宏、微观检测方法，对模具失效原因进行了分析。
Thus failure analysis was conducted for the steel dies using macro and micro test methods.
简叙了电站装备失效分析程序、失效原因及其失效机理。
This paper briefly introduces the procedures in failure analysis and the causes of failure in power-station equipment.
分析变换气冷却塔失效原因，认为主要是电偶腐蚀造成的。
This paper analyzes the failure reasons of the shift gas cooling column.
通过对齿轮失效原因的分析，提出了若干可行的预防措施。
Through analyzing the causes of the gear failure, this paper puts forward some feasible measures for preventing the gear failure.
帮助生产线分析工艺失效原因，提高良品率，改善过程能力。
Support production line to do process failure analysis and product diagnosis. Continuously optimize process and CPK etc.
分析了常规熔炼钢制造的铝型材热挤压模的失效原因及影响因素。
The failure reasons and effect factors of thermal extrusion mould of aluminium product manufactured by conventional smelting steel were analyzed.
简叙了石油化学工业装备失效分析程序、失效原因及其失效机理。
Procedure of failure analysis and the causes of failure in petrochemical equipment are discussed briefly in this paper.
从设计、制造和使用三方面对失效原因进行分析，并提出改进意见。
It also analyzes the reasons of losing efficacy in design, manufacturing and use. An opinion for improvement is put forward.
叙述了液压系统橡胶密封的原理、失效原因和对失效所采取的措施。
This article talks about the principle of rubber seal in hydraulic system, its failure and countermeasures.
分析了浮充型阀控铅酸蓄电池（VRLAB）的失效原因以及相应的解决办法；
The failure causes and resolving methods for floating charge of VRLAB were analyzed in this paper.
为了提高铝管冲头的使用寿命，用扫描电镜等手段对其失效原因进行深入分析。
In order to improve the lifespan of punch pin for al tube, the failure reason was carefully analyzed by SEM.
介绍了现用带阻尼翻板凳的阻尼原理，分析了其失效原因，并提出了改进建议。
The damping principle of the existing damping turnover stools is described. The causes to failure are analyzed. And suggestions for improvement are put forward.
本文探讨了液体静压轴承的失效形式，分析了失效原因以及提出了解决的措施。
This paper explores forms of failure in liquid hydrostatic bearing, analyzes their causes and puts forward measures to solve them.
在分析烧结机台车炉篦条失效原因的基础上，进行了提高它们使用寿命的材质研究。
On the basis of analyse of the invalidation cause of bar grate, the material research to increase the durability had been carried through.
分析其失效原因为铅合金在外力作用下，产生塑性变形引起的低周疲劳，造成断裂。
Through analysis, the failure reason was confirmed as that the low cycle fatigue caused by plastic deformation occurred in the lead alloy, thus the fracture occurred.
对浆料输送泵轴封失效原因进行分析，通过对轴封结构进行改进，取得良好密封效果。
The reasons on oil seal of filling carrier pump losing efficacy are analyzed. Transformation of oil seal structure is made, and good seal effect can be gained.
对高风压潜孔钻头使用时钻头体崩块、掉齿等早期失效情况进行分析，找到其失效原因。
The failure cause was found by analyzing high pneumatic down-the-hole bit bursting crack and the other reasons in the early stage.
应用化学分析、金相和电子探针显微分析技术对反应器中冷却水管的失效原因进行了分析。
Reasons of failure in cooling pipe of the reactor have been studied by the chemical composition analysis, optical microscopy examination and electron probe microanalysis.
本文针对湿法脱硫中不锈钢脱硫塔的防腐失效原因进行了分析，并采取了相应的防腐措施。
This paper analyzed the reasons of the invalidation of the corrosion protection measurements in the stainless steel desulfurizer, and relevant anti-corrosion measurements were introduced.
分析了原进口焊缝烘炉的基本结构和失效原因，介绍了新的焊缝烘炉的设计方案和结构特点。
The structure of a kind of imported seam welding electric oven and its failure reasons were analyzed. A new improved design for this kind of electric oven was introduced.
对新型精铸模具钢制热锻模具的失效进行了分析，并对不同形式下模具的失效原因作了探讨。
The failure dies of hot forged cast dies made by a new type of cast steel have been analyzed. The failure causes of different failure patterns are discussed.
对引起螺纹孔延伸公差带失效原因的各种因素进行了分析，并对采取的预防措施进行了讨论。
Many factors which possibly lead to failure of extended tolerances of threaded holes are analyzed, and a discussion on the method of prevention is made.
对软基底薄膜热敏电阻器的可靠试验进行了研究，由试验数据找出失效原因，并提出改进措施。
Reliability test of flexible substrate thin-film thermistor is researched. The reasons of failure from the testing date are found and improved advices are pointed out.
对软基底薄膜热敏电阻器的可靠试验进行了研究，由试验数据找出失效原因，并提出改进措施。
Reliability test of flexible substrate thin-film thermistor is researched. The reasons of failure from the testing date are found and improved advices are pointed out.
应用推荐