除了自动复位的故障以外，其它可远程复位控制故障引起的原因有以下几种：风机控制器误报故障；
In addition to automatically reset the fault, other faults can be caused by a remote reset control for the following reasons are several: fan controller, false failures;
帧复位在用户通过重新设定照相机用于新的帧扫描的控制情况下结束。
Frame reset ends frames under user control by resetting the camera for new frame scanning.
全数字化线路开关和单片机控制服务复位时间。
Fully digital line switching and MCU controlled service reset timing.
PLC控制系统将完成手动控制成形，自动控制精确成形，复位等功能。
PLC control system will be completed forming manual control, automatic control precision forming and reset functions.
关键还是对于动作轮控制器按钮可能需要绑定按键复位正确显示。
The key or controller button for the emote wheel may require the reset of the key-bindings to show up correctly.
改造技术研究，提高暖通空调系统明星一站式次连同空气旁路，复位和挫折控制被认为是最赚钱的。
Of the retrofit techniques investigated, improved HVAC system star-stop times together with air-bypass, reset and setback control was found to be the most lucrative.
而合适的复位弹簧刚度可以在不显著减小隔震效果的情况下有效地控制滑移位移。
The sliding displacement can be controlled by the right stiffness of spring under the circumstance that the effect of isolation doesn't decrease too much.
该IP核能实现对智能卡的探测、电源管理、复位和读写控制等功能。
The IP core has the function of detecting smart card, managing power, resetting, controlling reading and writing etc.
设置了自复位式按钮控制去磁和检测两个操作程序。
A self reset type button is arranged to control the demagnetizing operating program and the detecting operating program.
批处理控制器的程序控制开关用于启动，复位及停止批程序。
The sequence control switches of batch controller are used to start, reset and stop thd batch sequence.
从软件与硬件两个方面介绍了如何在MCS-51单片机控制系统中使用看门狗技术，对看门狗监控复位后的故障处理方式提出了一些解决方案。
This paper introduces how to use watchdog technology in MCS-51 single-chip computer control system from hardware and software two sides.
当访问硬盘时，即使失败，仍须复位磁盘控制器。
While accessing the hard disk, a disk controller reset was needed, but even that failed.
调查改造技术包括空气旁路控制冷却线圈，复位和挫折控制，提高暖通空调系统起止时间和节约外进气口。
Investigated retrofit techniques included air-bypass control on cooling coils, reset and setback control, improved HVAC system start-stop times and economizing on outside air intake.
存储单元和数据线用复位信号来控制，以使数据可在该半导体器件中被可靠地输出。
A memory cell and a data line are controlled with a reset signal, so that data can be reliably outputted in the semiconductor device.
偏振控制器要求有快的响应速度，大的消光比，小的波动，并能无端复位或不需复位就可进行无端偏振态控制。
It requires fast response speed, big extinction ratio, small fluctuation with endless reset or reset-free SOP control.
复位芯片与控制芯片连接，为控制芯片提供看门狗功能。
The recovery chip is connected with the control chip for providing the function of watchdog for the control chip.
方法：手术先将髂内外动脉做血流控制术后，行骨折复位、松质骨拉力螺钉固定共2 1例。
Method:After controlling the blood flow of the internal and external iliac arteries in 21 cases, the fractures were reduced and fixed with lag-screws of cancellous bone.
控制器的结构包括电源电路、控制电路、互锁电路、延迟复位电路、启动记录仪和声音指示电路、互锁电路。
The controller comprises a power circuit, a control circuit, an interlock circuit, a delaying reset circuit, a startup recording meter, a sound indication circuit and an interlock circuit.
通过设置812IE寄存器、初始化CAN控制器并将其置为复位模式、配置控制器寄存器并置为正常工作模式等，可实现CAN通讯。
After configuring IE register in AduC812, initializing CAN Contrloller and configuring it into normal modes etc, The communication on CAN Bus began.
在将内部复位信号加到CPU的同时，提高由DRAM控制器所生成的用于刷新DRAM中数据的刷新信号的速率。
While the internal reset signal is being applied to the CPU, the rate of a refresh signal being generated by a DRAM controller for refreshing data in DRAM is increased.
然后，当使外部复位信号无效时，生成一个延迟的复位信号并将其加到DRAM控制器以将其复位。
Then, when the external reset signal is disabled, a delayed reset signal DLYRST is generated and applied to the DRAM controller so that it is reset.
采用程序上电复位后读取系统关键状态的方法提高了控制系统的抗干扰性和可靠性。
The reliability of control system is increased remarkably with reading system working status when the control system is starting.
对其运动特性、越障性能、自动复位功能进行了详细的分析。采用的嵌入式控制系统保证了机器人功耗低、可靠性好、实时性高的控制要求。
The embedded control system is adopted to ensure the robot to be with low power consuming, good reliability and high real-time character.
对其运动特性、越障性能、自动复位功能进行了详细的分析。采用的嵌入式控制系统保证了机器人功耗低、可靠性好、实时性高的控制要求。
The embedded control system is adopted to ensure the robot to be with low power consuming, good reliability and high real-time character.
应用推荐