当输送机填充系数超过0.45时将不能采用这种卸料方法。
This unloading method cannot be used when the fill factor of the conveyor is over 0.45.
另外,介质筒的介电常数,填充系数等都对色散曲线有影响。
In addition, the dielectric parameter and the filled coefficient also have influence on the dispersion curve.
考察了填充系数对力学性能的影响,包括表面硬度、冲击强度和弯曲强度。
The influence of filling coefficient on mechanical properties, including surface hardness, impact and flexural strength, are investigated.
研究表明,掺加二灰后级配碎石混合料的性能显著提高,特别是二灰的填充系数为0。
The results show that the performances of graded gravel mixture are improved significantly after being treated with cement and lime, especially when fill factor is 0.
因此,实现了零间隙,即,在微透镜之间不存在 间隙,微透镜的填充系数被最大化。
Thus, a zero gap is realized, where no gap between micro lenses exists, and the fill factor of micro lens is maximized.
通过理论计算与试验结果的对比,建议冠状铆钉干涉配合的填充系数可取为0.474。
Based on the comparison between theoretical calculation and test results, this paper suggests that the filling coefficient of coronary rivet should be at 0.474.
物料在失重和同质状态下仍不受纯度、密度和填充系数的影响,混合速时间短,均匀度高。
High mixing speed and homogeneity. Materials can be mixed under the state of weightlessness and homogeneity and are not affected by the factors such as fineness, density and fill-up coefficient.
提出了填充系数理论,制订了土体渗透破坏形式的填充系数判别式和管涌临界破坏坡降计算图。
The filling coefficient theory was put forward, a criterion for the filling coefficient of soil stratum failure and a critical hydraulic gradient chart were formulated.
采用模塑成型和嵌入成型两种方法,通过改变体积填充系数、质量填充系数和芯体尺寸,制备了梯度密度聚氨酯泡沫塑料。
Gradient-density PUF was produced in two ways : mould shaping and embed shaping, through changing volume filling coefficient, mass filling coefficient, and the size of foam core.
该设备填充系数大,可达90%以上,对密度差别大、配比悬殊(可达1:24 00)、粒度不等的粉料的混合也同样适用。
It is used for a wide range of powder material with high density difference (up to 1:2400) with charging coefficient up to 90%.
对双层组合套管内填充液体介质进行了力学分析,导出了该介质压力传递系数的具体表达式。
A mechanical analysis on liquid medium filled in double-layer combined casing was conducted. An expressing equation of pressure transfer coefficient of the medium was deduced.
近年来填充床反应器CFD数学模型韵几个研究重点是动量交换系数、毛细管压力以及床层空隙率的非均匀分布性。
Several of the focuses of CFD model in packed-bed reactors were studied, namely, the momentum exchange coefficient, the capillary pressure and the void fraction.
塞贝克系数随着温度的升高和Y填充分数的增加而增大,同时峰值朝低温方向移动。
Seebeck coefficient increased with increasing temperature and Y filling fraction, the maximum value of Seebeck coefficient shifted towards low temperature.
随着LED芯片发光效率和散热技术的快速提升,显示屏分辨率越来越高,目前填充因子系数已达到10%。
With the rapid promotion of the LED chip light-emitting efficiency and heat dissipation technology, the fill factor coefficient of the LED display has been up to 10%.
通过考察体积传质系数,确定了纤维液膜萃取分离器的最佳填充密度和最佳流量比。
By analyzing the volume mass-transfer coefficient, the optimal operating flow-ratio and packed density were obtained.
讨论了不同填充比下固有频率对应的衰减系数关系曲线,得出了衰减系数随着大阻尼材料填充比的增大而增大。
It finds that the damping coefficient is directly proportional to not only wave frequency, but the filling fraction of bigger damping material.
分析了填充型高分子复合材料的导热机理,并预测复合材料导热系数的数学模型。
Thermally conductive mechanism and models that can predict the thermal conductivity of filled polymer composites are introduced.
提出了计算波束阻挡系数的平均值距离库填充法。
Firstly, a method to calculate the beam blockage coefficients is suggested.
提出了计算波束阻挡系数的平均值距离库填充法。
Firstly, a method to calculate the beam blockage coefficients is suggested.
应用推荐