介绍了一种弹塑性状态轮盘的实验应力换算新方法。
In this paper, a new method on experimental strain stress conversion of elastoplastic rotating disc is described.
对塑性状态下切削硬脆材料的方法进行了归纳和分类。
The way of cutting hard brittle material in a plastic state is classified.
提出了在塑性状态下切削非金属硬脆材料的加工思路。
This paper introduces a new processing think of cutting hard brittle material in a plastic state.
盐岩又是良好的盖层，且在高温、高压下呈塑性状态。
Meanwhile, halite is also a good cap rock, and would be in plastic state under high temperature and high pressure condition.
塑性形变压力是岩石由弹性状态转变为塑性状态所产生的压力。
Plastic deformation pressure is the pressure caused by changing the status of rock from elasticity into plasticity.
应用参变量变分原理推导了复合模量在弹性及塑性状态下的解析解。
The analytical solutions of composite modulus in both elastic and plastic conditions are deduced by applying parametric variational principle.
采用允许部分截面进入局部塑性状态的设计方法，相比弹性设计结构的承载力大为提高。
The design method which allows some sections to be part-plastic can improve load-carrying more greatly than elastic design method does.
当荷载不断增大，土体进入塑性状态后，土层承压能力减弱，锚桩的影响将很小，可以忽略。
When the load is becoming larger, the soil bearing press capacity will weaken after the soil enters the plastic state, thus the effect of the anchor pile will be little, so it can be neglected.
提出了轮盘进入塑性状态的鉴别方法、在塑性状态下求出割线模量和横向变形系数的方法等。
The method for identification of plastic state of the disk, as well as the approach to obtaining the secant module and transverse deformation coefficient are presented.
其他塑料可以二次通过再热的方式恢复到可塑性状态，这些是热塑性塑料，如丙烯酸树脂，尼龙和聚乙烯。
Other plastics can be repeatedly reheated to return to the plastic state; they are thermoplastics. Examples of thermoplastic plastics are acrylics, nylon, and polyethylene.
依据井壁围岩是否达到临界塑性状态而不是弹性极限状态来判断井壁稳定性是气体钻井井壁稳定分析模型的特殊之处。
The peculiarity of this wellbore stability model is to determine whether the wellbore rock is in the critical plastic state rather than elastic limit state.
该技术可使套管在整个开采过程中一直处于弹性状态，不发生塑性变形，从而解决了套管热破坏问题。
This technology keeps the casing in an elastic state in the whole thermal recovery process without plastic deformation taking place, and thus resolves the problem of thermal casing failure.
本文应用基于多重剪切塑性本构模型和液化状态面的有效应力分析方法，探索了液化场地微型斜桩的抗震性状和桩土动力相互作用机制。
Herein an effective stress analysis method using a multiple shear plasticity model and a concept of liquefaction front was used to investigate the static and dynamic.
本文应用基于多重剪切塑性本构模型和液化状态面的有效应力分析方法，探索了液化场地微型斜桩的抗震性状和桩土动力相互作用机制。
Herein an effective stress analysis method using a multiple shear plasticity model and a concept of liquefaction front was used to investigate the static and dynamic.
应用推荐