在工程设计中，我们经常采用轴对称容器。
The axial symmetry container is usually applied in the engineering design.
在工程设计里也一样。
本文探讨了电气节能技术在工程设计中的应用。
This paper discusses the electrical energy saving technology applications in engineering design.
在工程设计计算中，分配管系统是个十分复杂的过程。
In engineering design, the system of flow distribution pipe is very complex.
介绍了二灰桩的应用原理及其在工程设计中的应用情况。
In this paper the application principle and application situation in the engineering design of two ash pile are introduced.
文章经过比较提出了在工程设计中如何应用压力式温度计。
This paper introduces how to use the pressure type thermometer in engineering design skillfully by means of comparison.
介绍恩德粉煤气化工艺、技术特点及在工程设计中的应用。
The Undok pulverized coal gasification technology, its characteristics and application in engineering design were introduced.
在工程设计中，当条件相近时，直接用该公式设计是可行的。
While in a similar condition, it is effective to apply the empirical formula for engineering design.
飞行实验表明，文中所介绍的方法在工程设计中是简单可行的。
Flight experiments demonstrate that the analysis method is simple and feasible in engineering design.
在工程设计领域，CAD技术的应用大大提高了设计及绘图效率。
In the field of engineering design, CAD technology greatly enhanced the efficiency of design and graphics.
在工程设计寻求结构体积最小方案时，应同时考虑啮合角的优化问题。
While seeking the scheme of minimum structural volume in engineering design, the optimization issue ought to be considered at the same time.
在工程设计中，常遇到连续变量和离散变量同时存在的错综复杂问题。
In engineering design there exist the complicated problems on continuous and discrete variables.
因此在工程设计中选用TA时，需要采取恰当的措施来减轻TA饱和的影响。
So if we use ta in project design, we should take measures to relieve the influence of ta saturation.
从而为在工程设计中铜铝复合柱翼型散热器的选用与配置，提供了理论依据。
The fitting formula can provide the gist for deploying and choosing the copper-aluminum column-wing-type radiators in the project design.
在工程设计中，需针对不同的工作环境和工作模式，采用灵活的能量分配模式。
In engineering project work, flexible distributing energy mode should be selected in difference operating condition and operating mode.
主要介绍了多媒体技术、多媒体产品的性能以及多媒体技术在工程设计中的应用。
This paper describes the multimedia technology, the performance of the multimedia products and the applications of multimedia technology in engineering design.
数值计算表明，夹层板面层和芯层粘结处的层间剪应力在工程设计中是十分重要的。
Numerical calculations indicate that the transverse shear stresses at contact surfaces between face layers and core are very important in engineering design.
在工程设计中，遵循iec标准、电气设备编码规定、电气设计规范是十分重要的。
It is very important in engineering to abide with IEC standard, codification regulations of electric equipment and design codes for electricity.
根据工程实例，介绍卫生填埋场防渗方式的设计和各种防渗材料在工程设计中的应用。
Based upon actual projects, the article introduces design of impervious system of landfill and use of various impervious materials.
经验证，用此法计算出的风量、风压，可以在工程设计中较合理地选用空压机或鼓风机。
By verification, it showed that air volume and air pressure calculated with this method could be reasonably applied to engineering design for selecting air-compresses or air-blower.
该文分析了有关往复式氢压机在工程设计中的几个常见问题，从理论和实践上进行了探讨。
Some common problems of reciprocating hydrogen compressor in engineering design are analyzed, and discussed from the fields of theory and practice.
因此，工程人员在工程设计时，有一些工作是重复的、烦琐的，所以工程技术的效率难以提高。
Therefore, engineering personnel when the engineering designs, have the some work is repeated and trivial, the efficiency of engineering design is hard to increase.
在工程设计中，这是很重要的，估计可能发生的大地震，有用寿命内的结构(说，100年)。
In engineering design, it is important to estimate the likelihood of occurrence of a major earthquake within the useful lifetime of the structure (say, 100 years).
分析结果与算例指出，在工程设计时，一味追求高的灌水均匀度，往往会导致经济上的不合理。
Analytical results and a counting example show that it would unreasonable in economics if only a high irrigation uniformity is pursued.
为了解决锅炉水处理装置节能和安全运行问题，在工程设计中采用了计算机监控和数据采集系统。
In order to resolve the problems of energy saving and safe operation of boiler water treatment device, applies computer supervisory control and data acquisition system on engineering design.
通过若干经典算例，说明在工程设计中利用三维技术求解空间距离、空间曲线以及实体惯量的方法。
Through several typical calculating-examples, the methods of solving space distance and curve, and entity inertia by three-dimensional technology in engineering-design field were explained.
简单介绍了视频会议系统的技术标准和特点，并通过具体实例来说明在工程设计中应考虑的若干因素。
It briefly introduces video meeting system's technical criterion and features, explains some is - sues that should he considered in the project design by giving the practical examples.
简单介绍了视频会议系统的技术标准和特点，并通过具体实例来说明在工程设计中应考虑的若干因素。
It briefly introduces video meeting system's technical criterion and features, explains some is - sues that should he considered in the project design by giving the practical examples.
应用推荐