研究了圆台形纸杯（容器）的成型原理。
The forming principle of frustum cone-like cup (container) is studied.
所述的模具外形呈圆台状，具有一定的锥角；
The shape of each die forms a circular table shape, and each die has a definite cone angle.
在圆台表面上打有非压力下的弹性闭合状的孔口。
An opening is formed on the surface of each bench and adapted to close elastically under a non-compression condition.
本设计主要是针对圆台柱状巧克力糖的铝箔纸包装。
This design primarily aims at the circle pillar chocolates' aluminum foil packing.
三个最高的圆台容纳了约400个身披喇叭形斗篷的佛陀。
The three top terraces contain about 400 statues of the Buddha beneath bell-shaped coverings.
研究了二维椭圆台球中的量子谱和经典轨道之间的对应关系。
The correspondence between the quantum spectra and the classical orbits of the two-dimensional elliptic billiards is investigated.
所述圆台的任一边沿与圆柱套体相贯部位切去以形成一直边。
Any side of the circular table is cut along the penetrating part with the cylinder bushing body for forming a straight side.
阐述了等效圆台法的原理，以及此方法在异形接头展开中的应用扩展。
Application of equivalent round disk theory to optimization design on scoops of gas centrifuge;
本文提出采用“圆台二次包络啮合副”作为单螺杆压缩机啮合副的型线。
This lubrication film is easily established with "straight line enveloping screw pair" rotors, but this kind of engagement pair is very difficult to machine.
过载保护装置安装在减速机固定内齿轮圆台上、限位装置安装在机架下部。
The overload protection device is installed on a fixed circular table for the annular gear of the speed reducer and the position limiting device is installed on the lower part of a machine frame.
利用全反射原理，设计了特殊的圆台压平棱镜探头，可线性测量角膜的压平面积。
Based the principle of total reflection, the unique cone applanation prism is designed, by which the applanation area of ocular cornea can be measured linearly.
本文介绍了圆台压平棱镜的设计方法，给出了测量压平面积的实验装置和测量结果。
The method for designing cone prism is introduced, and the experimental device and results are also presented.
介绍了用于压平眼压计的圆台压平棱镜进行角膜压平直径线性测量原理及定位偏差分析；
The linear measurement principle of flattened diameter of the ocular cornea and the location deviation of the cone prism which is used in the applanation tonometer are introduced.
摘 要：本文着重介绍了海利普 变频器在立轴圆台平面磨床主轴调速控制中的应用。
Abstract: This paper introduces and researches the application of inverterHOLIP in spindle-speedcontrol of vertical shaft circular table plane grinding machine .
采用有限元计算编码abaqus模拟了钨合金圆台试件在冲击载荷下的变形和剪切局部化行为。
The deformation behavior and shear localization in truncated conic specimens of tungsten heavy alloys under impact loading are simulated by the finite element code ABAQUS.
当圆柱与圆台正交时，其相贯线可用一般方法作出，但其正面投影和水平投影上相贯线的最右点不能准确定位。
The line of intersection can be made with a general method when the cylinder and frustum of a cone are normal to each other.
角柱冲切破坏锥体近似1/4圆台体，边柱冲切破坏锥体近似1/2圆台体，中柱冲切破坏锥体为一个完整的圆台体。
The punching failure cone of comer column is approximately 1/4 round estrade, that of border column is approximately 1/2 round estrade and that of center column is completely one round estrade.
角柱冲切破坏锥体近似1/4圆台体，边柱冲切破坏锥体近似1/2圆台体，中柱冲切破坏锥体为一个完整的圆台体。
The punching failure cone of comer column is approximately 1/4 round estrade, that of border column is approximately 1/2 round estrade and that of center column is completely one round estrade.
应用推荐