结果发现，铜固溶在钨中，并形成了置换固溶体。
The results show that Cu solubilizes in W and the substitutional solid solution is formed.
晶粒生长指数随固溶温度的升高而增加。
Grain growth exponent increases with the increasing of solid solution treatment temperature.
材料经固溶处理后析出物绝大多数都溶入基体。
Most precipitate dissolve into the matrix after solution treatment.
对比测定了经固溶处理和未经固溶处理锯条的锯切性能。
The cutting performances of saw blade by solution and non-solution heat treating were determined.
将摘要固溶强化并与本堂课的新观念-析出强化进行比较。
Solid solution strengthening is summarized and compared to the new concept for this lecture: precipitation strengthening.
研究合金的强化机制包括固溶强化、加工硬化及析出强化。
The strengthening mechanisms of the alloy mainly include solution strengthening, strain-strengthening and aging strengthening.
重要的是较低的锻造温度和热处理固溶温度比较高的好得多。
It is important to control the forging temperature and solution treatment temperature lower rather than higher.
多元膜层强化机理主要是：晶粒细化、固溶强化、多元素优化。
The main strengthening mechanisms of (Ti, Cr)N films were grain fining, solid solution strengthening and multi elements strengthening.
理论分析表明：硼对沉淀强化、固溶强化和晶界强化均有贡献。
Theoretical analyses have shown that boron benefits precipitation strengthening, solution strengthening and grain boundary strengthening.
电子屏蔽理论分析表明，电场作用增大了溶质在晶内的固溶能力。
The electron shield theory analysis shows that the electric field improves the solute solubility.
采用固溶过时效处理之后，耐磨性优于正常固溶时效处理的试样。
Compared with the samples prepared by normal aging treatment, the test samples prepared by overaging treatment have better wear resistance.
研究了不同固溶处理对双相铸造不锈钢的组织及其耐蚀性能的影响。
The influence of different solid solution treatment on the structure and corrosion resistant property of cast duplex stainless steel was investigated.
结果表明，固溶处理状态下母材氩弧焊时具有较低的冷裂纹敏感性。
The experimental results show that, under solution treatment condition, this alloy has lower cold-crack susceptibility.
认为固溶强化和第二相强化是加入合金元素强化镁合金的主要方式。
It is thought that solution strengthening and second phase strengthening are two main ways for improving mechanical properties of magnesium alloy.
从而在固溶态价电子理论的深度揭示了合金元素在马氏体中的力学行为。
Thus in the depth of the valence electron theory of solid solution the mechanical behavior of the alloy elements in martensite was shown.
固溶处理是改善和提高奥氏体不锈钢波纹管抗应力腐蚀能力的有效措施。
And solution treatment is the valid method to improve the anticorrosion property of the austenite stainless steel bellows.
实验表明，随着固溶温度的升高和固溶时间的延长，合金的相变点升高。
The experimental results indicated that with higher betatizing temperatures and longer betatizing duration, phase transformation temperatures of the alloys became higher.
研究了C194合金变形与固溶时效热处理工艺条件对其组织性能的影响。
This paper is about construction and characteristics of C194, which are effected by heat-treatment of solution and aging .
研究了均匀化处理、固溶时效、冷变形时效等对铬青铜显微组织和性能的影响。
The microstructure and properties of chromium bronze after homogenizing treatment, solid solution and aging treatment, cool deformation and aging was studied.
研究了固溶过程中施加的电场对合金时效后的性能、断裂特征和析出相的影响。
Influences of electric field applying during solution process on mechanical properties, fracture characters and precipitates in aged alloys are studied.
本文研究高温固溶处理对一种定向凝固高强度镍基高温合金的组织和性能的影响。
The effect of high temperature solution treatment on the structure and properties of a directionally solidified high strength nickel-base superalloy has been investigated.
通过低压铸造后固溶处理的方法，获得了网状金属间化合物增强铝合金表面复合层。
Intermetallic compound foam reinforced aluminium alloy surface composite layer are obtained by solution treatment after low pressure Casting.
研究了低频电磁半连续铸造7A60合金铸锭的合金元素在晶内的固溶状况和力学性能。
The intracrytalline solubility of alloy elements and mechanical properties of 7A60 Al alloy billets cast by low frequency electromagnetic casting were investigated.
平均直径的变化是先减小，在2小时左右到达最小值，然后，随着固溶时间的延长而增大。
But the diameter average decreases at first, approaches to the minimum after treated 2 hours, then increases with the solution time.
介绍了铝轮毂固溶热处理联合电炉的设计方法、结构特点、炉子组成以及需要注意的问题。
The design methods, the structure characteristic, the composition and other problems of the Aluminum wheel hub solution heat treatment combined electric furnace were introduced.
此外，喷瓷管道焊接热影响区的金属基体将由于喷瓷过程中渗入的固溶氮而产生大量微裂纹。
In addition, the metal body within welding heat effect zone will produce a lot of micro-cracks because of infiltration of solid solution nitrogen in course of porcelain spraying.
结果表明：多重固溶时效热处理可以显著提高合金的塑性和断裂韧度，而对强度的影响不大。
The results showed that multiple solution and aging treatment had a significant effect on increasing plastic property and fracture toughness, although had little effect on strength.
文章利用自行开发的固溶物沉积激光测试系统，测试了凝析气平衡油在不同压力下的析蜡温度。
Using the laser testing system of soluble solid deposition developed by themselves, the wax-condensing temperature of equilibrium oil of condensate gas is tested under different pressure.
文章利用自行开发的固溶物沉积激光测试系统，测试了凝析气平衡油在不同压力下的析蜡温度。
Using the laser testing system of soluble solid deposition developed by themselves, the wax-condensing temperature of equilibrium oil of condensate gas is tested under different pressure.
应用推荐