研究了DGEBP的固化反应。
用IR和DSC技术检测了树脂的固化反应；
Thecure reactions for the resins were determined by IR and DSC techniques.
结果表明，改性体系的固化反应活性略有降低；
The results showed that the curing activity was slowly depressed.
讨论了清漆的溶剂选择、固化反应机理和红外光谱表征。
Selection of solvent mixture, curing mechanism and IR spectrum characterization were discussed.
结果表明，CTBN对DCPDCE的固化反应具有催化作用；
The results showed that CTBN had catalytic action on the curing behavior of DCPDCE.
一种专门的化学材料，可以提升或促进固化反应或降低烘烤温度。
A special chemical that promotes or accelerates the curing reaction or reduces stoving temperature.
研究了DCPD酚环氧树脂与酸酐及胺类固化剂的固化反应活性。
It was studied on the curing activity of DCPD phenol epoxy resin with anhydrides and amines.
讨论了该清漆的溶剂选择、配方代化、固化反应机理和红外光谱表征。
The article has discussed the selection of solvents, formulation optimization, curing mechanism and IR characterization.
试验结果表明，该环氧树脂体系的固化动力学符合自催化固化反应模型。
From the experimental data, it was found that the autocatalytic cure kinetic modeling correctly represented the cure kinetics of this system.
利用固化反应动力学模型对复合材料成型工艺的固化工艺进行了模拟计算。
The simulating calculation of composite curing process was carried out by means of cure kinetic model.
利用流变仪和热分析仪对213#酚醛树脂的流变行为和固化反应进行了研究。
The rheological behaviors and curing properties of 213# phenol resin were studied using a rheometer and a differential scanning calorimeter.
本文合成了三种咪唑盐，并就其固化反应特点及对固化物性能的影响作了初步探讨。
Three kinds of imidazole salt were synthesized. The characteristics of their curing reaction and the effect of the characteristics on the properties 0f the cured product were investigated.
利用傅立叶变换红外光谱对纯氰酸酯及其改性树脂体系进行固化反应动力学的研究。
The kinetics of neat cyanate ester and its modified resin systems were investigated by FTIR.
固化反应过程及固化机理与促进剂作用下酸酐固化双酚A型环氧树脂的反应基本相同。
The reaction process and curing mechanism were basically identical to the curing reaction of bisphenol A epoxy resin with anhydride in the presence of accelerator.
用FT - IR和DSC技术检测了树脂的固化反应；最后对树脂的性能进行了表征。
The curing reaction of the resin was investigated by using FT-IR and DSC technique and the characteristics were described.
利用红外光谱、差示扫描量热法分析技术对改性树脂的结构及固化反应过程进行了研究。
The structure and curing of the modified phenol resin were investigated by means of IR spectra and DSC methods.
在较高温度和较低纤维含量条件下，离子导电率变化较快，对树脂固化反应的影响较大；
In the case of high temperature and low fabric volume fraction, the ionic conductivity changes dramatically, which in turn has a significant influence on the resin curing process.
运用示差扫描量热(dsc)法研究了邻苯二甲酸二烯丙基酯(DAP)树脂的固化反应历程。
Curing reactions of diallyl phthalate (DAP) resin were studied by differential scanning calorimetry (DSC).
用动力学扭辫分析(tba)法研究了水溶性丙烯酸酯树脂与六甲氧基甲基三聚氰胺的固化反应。
The curing reaction of waterborne acrylic resin with HMMM has been studied by using the torsional braid analysis (TBA).
随着单体溶液浓度、固化反应温度、引发剂和催化剂加入量的提高，凝胶固化反应速率快速增长。
The rate of solidification process increases with the concentration of the monomer solution, gelation temperature and the amount of the initiator and catalyst.
本文研究了有机过氧化物引发剂对低介电损耗的改性双马来酞亚胺树脂4501A固化反应的影响。
In this paper, effects of peroxide on curing reaction of modified BMI resin (designed as 4501a) with low dielectric loss were studied.
借助TG、DSC、SEM和TEM对改性酚醛树脂体系的耐热性能、固化反应和微观形态进行了表征。
Heat resistance, curing reaction, and morphology of the modified phenolic resin system were characterized by TG, DSC, SEM and tem.
采用非等温差示热量扫描DSC曲线方法探讨了竹材液化物酚醛树脂胶不同物质的量之比时的固化反应过程。
The curing reaction process of bamboo liquefaction phenolic resin with different molar ratio was studied by non-isothermal differential scanning calorimetry(DSC).
并模拟实际固化温度历程，采用测定不同固化阶段样品残余反应热的方法对固化反应动力学方程进行了验证。
By simulating practical temperature procedure of curing, the cure kinetic equations were verified by means of determining the residual heat of reaction of samples with different cure degrees.
采用差示扫描量热（DSC）和热失重分析（TGA）研究了含萘环结构的氰酸酯树脂的固化反应和耐热性能。
The cure reaction and thermal properties of a novel dicyanate ester resin containing naphthalene ring were characterized by differential scanning calorimetry(DSC) and thermogravimetric analysis(TGA).
采用全动态dsc研究了双马来酰亚胺树脂(BMI)体系的固化反应动力学，建立了固化动力学的唯象模型。
The cure kinetics of bismaleimides (BMI) resin system was investigated by dynamic DSC analysis and the phenomenological model was established.
通过热分析方法、推进剂配方工艺研究与性能测试，探讨了它们对NEPE和丁羟固体推进剂固化反应的催化作用。
Their catalytic activities to the curing reaction of NEPE and HTPB solid propellants were studied by thermal analysis methods, formulation process research and performance test of propellants.
合成了一系列不同结构的丙烯酸聚氨酯预聚物，重点讨论预聚物的分子结构及相对分子质量对紫外光固化反应的影响。
A series of acrylic-polyurethane resin with different structure were prepared, and the influence of the structure and molecular weight of the polymers on UV-curing reaction was studed.
合成了一系列不同结构的丙烯酸聚氨酯预聚物，重点讨论预聚物的分子结构及相对分子质量对紫外光固化反应的影响。
A series of acrylic-polyurethane resin with different structure were prepared, and the influence of the structure and molecular weight of the polymers on UV-curing reaction was studed.
应用推荐