冰川的变形量涉及哪些因素？
What factors are involved in the amount of deformation a glacier undergoes?
热变形量往往超出允许的误差。
加速底板施工是控制底板总变形量的关键。
To speed up the bottom slab construction is the key point for controlling the deformation generally.
细颗粒砂土比粗颗粒砂土具有更大的变形量。
Sandy soil with fine grains has more deformation than sandy soil with coarse grains.
合理地确定预拉伸变形量才能合理的利用材料。
In order to make Use of the material rationally, the pre-tension deformation should be reasonably decided.
合金的形状回复率随着预变形量的增加而减小。
The shape recovery decreases with the increasing of predeformation amount.
通过选择适宜的工艺参数可减少淬火板的变形量。
The amount of quenching deformation of plate can be decreased by chosing proper parameters.
弹簧的变形量与施加在其上的作用力成线性关系。
Deformation of a spring is linear with the force applied on it.
冷变形量及时效温度是影响交互作用的主要因素。
The degree of cold rolling and aging temperature are the major factors that influence the interaction.
变形量越大，则再结晶温度越低，晶粒尺寸越小；
The lower the recrystallization temperature, the smaller is the grain size.
推导了组合型密封环的压缩变形量及接触压力的计算公式。
The calculation methods of deformation and contact press force of sealing rings are derived.
针对膨胀土特殊工程性质，分析了胀缩变形量的影响因素。
Based on special engineering properties of expansion soils, influence factors of swell-shrink distortion are analyzed.
并以腰鼓变形量是否超过临界值作为焦炭塔判废的标准之一。
One of criteria for coker drum invalidation is whether the loin-drum deformation has exceeded the critical value.
工艺上可以通过调整延迟时间和气体压力来减小产品的变形量。
Adjusting delay time and gas pressure can reduce the warpage of the part.
结果表明，适当的预冷变形量对改善合金塑韧性有较明显的作用。
The results show that suitable cold pre-deformation can improve the alloy's plasticity and toughness obviously.
针对飞机叶片表面变形量测量要求提出一种非接触式光学测量方法。
This paper presents an untouched optical measuring method in finding out the deformation of an aircraft engine vane.
在同一变形条件下，虽然变形量不同，但是过冷温度区间基本不变。
At the same deformation condition, the supercooled temperature range is almost invariable although deformation degree are different.
以激光为热源的焊接同样也可以得到低热输入、变形量极少的效果。
Weld whose heat resource is the laser, also owns the advantage such as low heat input and small heat deform.
研究表明：随变形量的增加，合金丝的电阻率升高，上述热电势降低。
The study shows that the resistivity of alloyed wire raised and thermal potential reduced with the increase of deformation.
对不同锻造变形量的钨合金材料组织、性能及其再结晶行为进行了研究。
The investigation was made on microstructure, mechanical property and recrystallization behavior of tungsten alloy with different amount of swaged deformation.
该模型通过预测坯壳应力和鼓肚变形量为现场安全生产提供了理论依据。
The model can provide the theory for the field safety production by the prediction of shell stress and dilatancy distortion value.
这不仅提高生产率，而且能减少被割零件的变形量和割缝区的热影响区域。
This not only increase productivity, and cut parts can reduce the deformation and cut the heat affected zone seam.
给出了激光模式之间的耦合以及等效光束发散角与镜面变形量之间的关系。
The coupling among laser modes and the relations between equivalent beam spread Angle and the surface deformation of the mirrors are obtained.
此外，为了提高活塞环润滑性能应尽量减少气缸套和活塞环的径向变形量。
Also, the radial deformation of cylinder liner and piston ring should be reduced to improve the lubrication performances of piston ring.
当预变形量相同时，含0.12%碳的合金的形状记忆效应低于超低碳合金。
The shape memory effect of the alloy with 0.12% carbon was lower than the alloy with ultra-low carbon.
实验还观察到随着塑性变形量的增加，变形带的倾斜方向会发生对称迁移现象。
And with the increase of the plastic deformation, the inclined direction of the deformation bands takes place a symmetry change.
结果显示：AZ 31镁合金铸轧组织对应变速率和变形量均具有较强的敏感性。
The results show that the microstructure of continuously roll-cast AZ31 alloy is sensitive to both strain and strain rate.
它不仅能提高持力层的承载力，减少地基变形量，同时还可以加速地基的排水固结作用。
It can not only increase the bearing capacity of supporting course, but also reduce the deformation modulus of the foundation and accelerate the drainage and consolidation function of the foundation.
在研究轧制工艺参数对轧制复合过程的影响时，重点探讨了轧制温度以及变形量的影响。
While studying the rolling influence of the course to rolling compounding of craft parameter, have probed into the rolling temperature and influence of deformation amount especially.
在研究轧制工艺参数对轧制复合过程的影响时，重点探讨了轧制温度以及变形量的影响。
While studying the rolling influence of the course to rolling compounding of craft parameter, have probed into the rolling temperature and influence of deformation amount especially.
应用推荐