耐磨试验通常在常压条件下进行。
Abrasion tests are universally carried out under atmospheric conditions.
常用扦插。嫁接和压条繁殖，也可播种。
Commonly used cuttage, engraft and layering are progenitive, also can sow.
通过实验优化了夹流式进样的电压条件。
The condition of applied voltages for pinched sample injection was optimized.
这证明反复煮沸条件比减压加压条件恶劣。
This demonstrated that repeated boiling was more severe than vacuum-pressure.
繁殖常用扦插。嫁接和压条繁殖，也可播种。
Commonly used cuttage, engraft and layering are progenitive, also can sow.
我们对农作物进行压条处理，以利于他们生长。
分析了不同偏压条件下声光强度调制的波形失真。
Wave distortions in the intensity modulation on different bias conditions have been analyzed.
此外，本文还考察了常减压条件下MPC的歧化反应。
Furthermore, the disproportionation of MPC into DPC under atmospheric-vacuum condition was studied.
玻璃四周显露黑色密封边框，适用于周边压条镶嵌安装。
The black seal frame around of glass can be seen, it is suitable for inlaying installation with pressing strip around it.
设计了理想混合气体在等温等压条件下的可逆化学反应过程。
The reversible chemical reaction process of ideal gas mixture in the condition of constant pressure and temperature has been designed.
高温高压条件下，水的存在不利于碳质物的石墨化(有序化)。
The presence of water is unfavorable to the graphitization (ordering) of carbonaceous matter.
钢渣在蒸压条件下的膨胀粉化是改善其稳定性的一个重要方法。
The expansion pulverization of steel slag in the autoclave is an important way to improve its stability.
在较低围压条件下，岩石的压缩强度同围压系数具有线性关系。
On condition of low confining pressures, the simulating compression strength keeps linear relation with confining pressure's coefficient.
应用叠加原理建立了变流压条件下不稳定流量响应的数学模型。
Applying the superposition principle, the transient rate's mathematics model under the variable flowing pressure condition has been introduced.
对铝合金L F3Y 2搭接板进行了热压条件下激光深熔焊接。
Deep penetration laser welding was performed at aluminum alloy LF3Y2 under hot and press condition.
无围压射孔技术就是研究在高负压甚至无围压条件下实现射孔完井。
To solve this problem we developed a high negative pressure and confining pressure-free perforating process.
对不同钢纤维体积率的混凝土复合材料在不同围压条件下进行受压试验。
The press tests of composite concrete materials with different volume ratio of steel fiber have been carried out under different confined pressures.
本文着重介绍了不同的压条在设计中应该注意的各种不同问题及解决方法。
It introduces some problems that require attention during the design of different glass bead profile, and relative solving methods are carried out.
它是在某种催化剂参与下，由无水氨和二氧化碳气体在高压条件下反应生成的。
It is prepared by reacting anhydrous ammonia and carbon dioxide gas under very high pressure in the presence of a suitable catalyst.
压条是塑料异型材中截面很小的一个零件，但在整体装配中起着举足轻重的角色。
Glass bead profile, one of plastic special-shaped products with small cross-section, ACTS an important role in the process of integrated assembling.
模型首次直接对影响辊压过程的关键因素即基材材质和辊压条件进行了模拟分析。
The model directly simulate the blade material and rolling conditions, the key factors in rolling process for the first time.
麻粒岩和榴辉岩中退变质阶段的角闪石主要形成于中压相系角闪岩相的温压条件。
The amphiboles of retrogressive metamorphic stages in the granulite and eclogite were mainly formed under the condition of amphibolite facies of medium pressure facies series.
对于纯气体形成水合物，甲烷形成的温压条件最高，丁烷最低，乙烷和丙烷介于二者之间。
For simple gas hydrate formation, the temperature and pressure of methane hydrate is highest, butane is lowest, and ethane and propane is between them.
建立了膨胀岩在侧向约束，轴向加压条件下侧限膨胀应变与含水率、轴向荷载之间的关系。
A lateral restricted swelling constitutive relationship, in which the effect of water content and axial loading are considered, has been proposed.
运用石油与天然气生成理论，讨论了东濮凹陷深层异常温压条件下烃源岩热演化的异常现象。
By using oil and gas generation theory, the abnormal phenomena during thermal evolution of hydrocarbon source rock in the deep formation of Dongpu Depression were discussed.
运用石油与天然气生成理论，讨论了东濮凹陷深层异常温压条件下烃源岩热演化的异常现象。
By using oil and gas generation theory, the abnormal phenomena during thermal evolution of hydrocarbon source rock in the deep formation of Dongpu Depression were discussed.
应用推荐