本文统一分析了轴心压杆三种常用截面的板件宽厚比限值。
This article presents a unified analysis of the limiting slenderness of plate elements of compression members with three commonly used sections.
索杆张力结构是指由张力索和压杆组成的、具有预应力自平衡的新颖结构体系。
The cable strut tensile structures are the self stress equilibrium systems composed by tensional cables and struts.
索杆张力结构是指由张力索和压杆组成的、具有预应力自平衡的新颖结构体系。
The cable- strut tensile structures are the prestress equilibrium systems composed by tensional cables and struts.
压杆的失稳将导致结构的失效。
Buckling of struts would lead to invalidation of the structure.
按照汽车行驶时碰杆和压杆的次数评定成绩。
The result is evaluated according to the number of times of the rod touching and rod pressing when the automobile runs.
从德国进口的压铅机压杆在使用中表面严重划伤。
The pressure bar of a lead briquetting machine, imported from German, was seriously scratched during its service.
当手柄抬高到垂直位置,它就将可拆卸“压杆”压下。
When the lever is raised to the vertical position it pushes a removable "Push Rod" down.
单轴对称的角钢、T型钢压杆有必要做弯扭屈曲验算。
Struts of monosymmetric section built with angles and cut-Ts need to be checked on flexural-torsional buckling.
主要研究了楔形变截面压杆绕弱轴的弹塑性弯曲失稳。
The elastoplastic bending instability of the tapered compression members under axial loads about the weak axis is mainly studied.
在模型中加入压杆稳定约束,使智能桁架结构更加稳定。
The constraint of press stability was added and the structure was more stable.
通过一个例子说明微分变换法在压杆稳定问题中的应用方法。
The application of the differential transformation method is demonstrated by an example for stability problems of columns.
对一端固定一端自由功能梯度压杆的后屈曲问题进行了分析。
Post-buckling equilibrium paths of functionally graded material(FGM)rectangular bar with one end fixed and another end free are studied.
介绍了用于减小压杆计算长度的侧向支撑的强度和刚度设计要求。
The stiffness and strength requirements for the lateral bracings reducing the calculation length of the compression struts are introduced.
计算发现,压杆模型或软化桁架模型所分配到的外荷载并不平衡。
The calculation results revealed that the loads carried by the compression strut or the softened truss model were not in equilibrium.
本文分析了受短时热冲击压杆在非均匀温度场下的蠕变屈曲问题。
The creep buckling of columns with geometrical imperfections subjected to short time heat input is studied in this paper.
在屋盖结构设计中,用钢管混凝土轴心受压杆件作为网架的压杆。
In the roof cover structure design, the steel tube con - Crete axis pressed rod was used as a press rod of network frame.
压杆机构采用油压自动平衡系统,压杆高低不需要调整,操作简单。
The strut mechanism adopts automatic hydraulic balancing system. The height of strut is not necessary to make adjustment with simple operation.
阀瓣打开后,压杆在弹簧作用下旋转一定角度支住阀瓣,使其不能关闭。
When the disc is opened, with the springs at work, the strut rotates to an Angle so as to prop up the disc and keep it from closing.
限位开关多数情况下是机械式,并靠控制杆或压杆进行物理接触激发的。
Limit switches are most often mechanical and are activated by physical contact with either a lever or plunger.
求压杆临界载荷的方法很多:有静力法、矩量法、子域法、最小二乘法。
Many methods, e. g. static force method, moment method, sub-region method and least square method, have been used tog et the critical load.
我继续向左压杆,并且把油门从加力状态下收回以便不使飞机加速的太快。
I keep that left-hand turn going and bring the throttles out of full AB to make sure I'm not accelerating too much.
提出了基于压杆模型和软化桁架模型的钢筋混凝土梁柱节点抗震设计方法。
A seismic resistant design method of reinforced concrete beam-column connections based on compression strut and softened truss models was proposed.
本文介绍了摆锤冲击压杆测定岩石动态荷载—位移全过程曲线的实验技术。
The experimental techniques of measuring the rock complete loading displacement curve under the pendulum impact are introduced in this paper.
本文叙述了两种软化桁架模型,它们的区别是对混凝土压杆角度的假定不同。
This paper describes two types of softened-truss model, depending on the assumption for the Angle of concrete strutS.
在此状态下可在任意长度的压杆上,加任意大小的轴向载荷,而不产生弯曲。
With this situation, any amount of axial load can be applied to compressive bar of arbitrary length without bending.
因而对支承于弹性系统上的细长压杆,需考虑支坐变位对临界屈曲载荷的影响。
Thus, for the slender struts supported on the elastically system, the influence of the bearing deflection on the critical buckling load must be considered.
针对柔性套管约束杆件,研究了轴压杆件与约束杆件点、线接触时的约束屈曲。
The buckling of an axially compressive strut constrained by a flexible sleeve is studied for the cases of a single point contact and a curved line contact between the strut and the sleeve.
本文用解析法和有限元法分析了连续多支承压杆的稳定性及其近似解与精确解。
This paper analyzes the stability of continuous and multi-support compressed pillars using analysing method and finite element method.
本文给出了计算钢压杆弹塑性稳定极限承载力的有限条塑性系数增量初应力法。
The paper presents a numerical method, named the Finite Strip Plasticity Coefficient Increment Initial Stress Method, to solve the elastoplastic stability ultimate loads of steel columns.
本文给出了计算钢压杆弹塑性稳定极限承载力的有限条塑性系数增量初应力法。
The paper presents a numerical method, named the Finite Strip Plasticity Coefficient Increment Initial Stress Method, to solve the elastoplastic stability ultimate loads of steel columns.
应用推荐