我打不开门—卡死了。
另外还有一些做的粗糙的地方需要改进,比如:4s的照相机应用偶尔会卡死在启动界面。
There are some rough spots here and there; for example, every now and then the 4s's camera app gets stuck on its startup screen.
我无法操纵这辆汽车,车轮给卡死了。
阀芯与阀座或衬套卡死,阀杆弯曲等。
Valve core and valve seat or bushing deactivation, valve lever curving and so on.
应当注意,出口止回阀不能装反或出现卡死现象。
It should be noted that the outlet check valve cannot be installed backwards or stuck.
摧毁一个正在阅读的路牌不会导致你的角色卡死。
Destroying a placed sign while you are reading it will no longer cause your character to become frozen.
该方案考虑了两种舵机故障模型:舵机卡死和舵机失效。
Considered actuator fault models include both the actuator-stuck fault and the loss of actuator effectiveness fault.
本文研究无人机方向舵卡死时下滑模型建立的方法与处理原则。
This paper researches the method of modeling and principle of establishing model of unmanned aerial vehicle(UAV) during gliding with rudder lock-in-place.
当玩家将尼姆布亚的长矛插在地上的时候,不再会造成卡死的现象。
Players will no longer become stuck on the Nimboya's Laden Pike when driving it into the ground.
在洛阳石化总厂一年多的运行表明,操作方便,未发生阀轴卡死现象;
Application more than one year in Luoyang General Petrochendcal Works showed that it is characterized by convenient operation, good sealing property and no shaft seizing.
工矿企业电动机在使用过程中,由于机械出现故障造成扫膛、卡死、烧坏线圈等事故。
In the use of electric motor by enterprise, mechanical failure may cause accidents, which result in touch between stator and rotor or stop or damage of coil.
重点研究了盾构刀盘在切削过程中负载冲击和刀盘卡死产生的原因以及冲击带来的影响。
The impact load and its effect as well as the reason of cutterhead deadlocking were mainly studied.
油温升高使阀心受热膨胀,阀套与阀心间的配合间隙减小, 阀心有可能被卡死在阀套里。
The fit clearance between spool and sleeve decreases because of the thermal expansion of the spool caused by temperature increment, so it is possible that spool is deadlocked in sleeve.
由于定向井井身结构特殊,利用螺杆泵进行抽油时如不采取任何措施势必造成杆柱严重磨损甚至卡死。
Due to the special structure of controlled direction well, it can lead to severe abrasion even jamming if not adopting any measure when using progressing cavity pump rod to pump oil.
齿轮减速器的出轴与负载连接时不能重力敲打、挤压,以免造成内部变形走位,产生严重噪声或卡死现象。
No beat or squeeze when connect load to the outer axis of gear speed reducer so that not to arise deformation and dislocation, bad noise or locked dead.
针对挠性航天器执行器卡死与失效故障的姿态稳定控制问题,提出了一种结构简单、计算量小的改进型滑模容错控制策略。
A modified sliding mode fault tolerant controller is developed for flexible spacecraft attitude stabilization control in the presence of loss of actuator effectiveness fault and actuator stuck fault.
根据TK - 3型液压立轴式岩心钻机结构分析产生液压卡盘失灵、主动钻杆卡死等故障的原因,提出了两套改造方案。
Analyzed causation of TK-3 hydraulic vertical shaft coring drilling rig easy to bring hydraulic chuck failure, get stuck with actuating rod etc, put forward two alteration schemes.
本文提出的加压网前箱容错控制系统,在正常情况下具有解耦功能和期望动态品质,同时,对任意执行器和传感器卡死故障具有容错性。
This control system is decoupled and has good dynamic properties in the normal state, and has fault-tolerant capability against arbitrary actuator or sensor failures.
精细水煤浆在柴油机上燃烧一段时间后,油浆泵柱塞偶件经常出现卡死现象,原因是柴油机工作过程中油浆泵柱塞偶件间积存大量未燃烧的超细煤粉。
After fine clean coal water mixture has burnt in a diesel engine for a certain period of time, the plunger coupling parts in mixture pump are always jammed.
他们对一个卡死的旋转接头进行了检查,这个接头影响一套太阳能板的使用长达数月之久。最后他们成功地把一些实验设备吊运到欧洲实验室“哥伦布号”上。
They inspected a jammed rotating joint that has restricted the use of a set of solar wings for months, and finally succeeded in hanging some scientific experiments to the European lab, Columbus.
他们对一个卡死的旋转接头进行了检查,这个接头影响一套太阳能板的使用长达数月之久。最后他们成功地把一些实验设备吊运到欧洲实验室“哥伦布号”上。
They inspected a jammed rotating joint that has restricted the use of a set of solar wings for months, and finally succeeded in hanging some scientific experiments to the European lab, Columbus.
应用推荐